Manuals / BenQ / Computer Equipment / Projector

BenQ ms616st, mx618st user manual Advanced, See Hiding the image on page 31 for details

Models: ms616st mx618st

1 58

Download 58 pages 15.75 Kb

Page 43

Advanced

Function

	4.SYSTEM SETUP:Basic		Splash
	4.SYSTEM SETUP:Basic		Screen
			Screen
			Auto Blank
			Quick
			Quick
			Cooling
			High
			Altitude
			Mode
	5.		Audio
	SYSTEM		Settings
			Settings
	SETUP:		Settings
			Lamp
	Advanced		Settings
	menu		Settings
			Security
			Baud Rate
			Test Pattern

Description

Allows you to select which logo screen will display during projector start-up.

See "Hiding the image" on page 31 for details.

Enables or disables the Quick Cooling function. Selecting On enables the function and projector cooling time will be shortened from a normal 90-second duration to approximately 30 seconds.

A mode for operation in high altitude areas. See "Operating in a high altitude environment" on page 31 for details.

Mute

Volume

Power On/Off Ring Tone

See "Adjusting the sound" on page 32 for details.

Lamp Mode

See "Setting Lamp Mode as Economic or SmartEco" on page 46 for details.

Reset Lamp Timer

See "Resetting the lamp timer" on page 50 for details.

Equivalent Lamp Hour

See "Getting to know the lamp hour" on page 46 for details on how the total lamp hour is calculated.

Change Password

You will be asked to enter the current password before changing to a new one. See "Utilizing the password function" on page 21 for details.

Change Security Settings

Power On Lock

See "Utilizing the password function" on page 21 for details.

Selects a baud rate that is identical with your computer’s so that you can connect the projector using a suitable RS-232 cable and update or download the projector’s firmware. This function is intended for qualified service personnel.

See "Using the test pattern" on page 33 for details.

Operation 43

Image 43

BenQ ms616st Advanced, See Hiding the image on page 31 for details, See Adjusting the sound on page 32 for details

Contents

User Manual MS616ST/MX618ST Digital ProjectorMaintenance Table of contentsImportant safety Warranty and CopyrightSafety Instructions Important safety instructionsSafety Instructions Continued 3000 m 10000 feet 0 m 0 feet Ceiling mounting the projector Introduction Projector featuresStandard accessories Shipping contentsOptional accessories Front/upper side Projector exterior viewRear/lower side Focus ring Controls and functionsProjector LAMP indicator light10. Page Up/Page Down Remote controlReplacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size Projection dimensionsConnection Connecting audio Connecting video source devicesStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageto correct keystoning at the top of the Correcting keystoneUsing the menus If you forget the password Using a security cable lockUtilizing the password function Setting a password2. Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appears Entering the password recall procedureChanging the password Disabling the password functionChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailshorizontal or vertical width. This is suitable About the aspect ratioAuto Scales an image proportionally to fit 169 Scales an image so that it isOptimizing the image Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeAdjusting Color Fine-tuning the image quality in user modesAdjusting Brightness Adjusting Contrastto highlight Saturation and adjust 3D Color ManagementTo cancel the timer, perform the following steps Setting the presentation timerFreezing the image Remote paging operationsBe sure the SYSTEM SETUP Basic Auto Blank menu is On Hiding the imageLocking control keys Operating in a high altitude environmentTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Muting the soundUsing the test pattern Teaching Using the teaching templatesLetter Formation Worksheet Coordinate Chart to select Blackboard or WhiteboardSupported image formats When viewing thumbnailsSetting page Presenting from a USB ReaderShutting down the projector Direct power offMenu system Menu operationOptions SETUPMain menu Sub-menuMain menu SETUPReset Lamp Timer Change PasswordDescription of each menu See Adjusting Brilliant Color on page 27 for details See Using the teaching templates on page 34 for detailspicture mode on page 26 for details See Adjusting Contrast on page 27 for detailsSets the length of time the OSD will remain active after your last key See Utilizing the password function on page 21 for details See Adjusting the sound on page 32 for detailsSee Setting Lamp Mode as Economic or SmartEco on page 46 for details See Resetting the lamp timer on page 50 for detailsmenu Care of the projector MaintenanceCleaning the lens Cleaning the projector caseGetting to know the lamp hour Lamp informationExtending lamp life Install a new lamp for optimal performance. If the Timing of replacing the lampwhenever you notice that the brightness level has cover on the side of the projector until the lamp cover loosens Replacing the lamp48 Maintenance 2. Loosen the screw that secures the lamp6. Use the handle to slowly pull the lamp out of the projector Resetting the lamp timer Status & Description IndicatorsPower events LightPlease see Entering the password recall Troubleshootingprocedure on page 22 for details Projector specifications Specifications312 mm W x 104 mm H x 244 mm D DimensionsCeiling mount installation 54 SpecificationsPixel Timing chartSupported timing for PC input UXGA56 Specifications Supported timing for HDMI HDCP inputPixel Timing Supported timing for Component-YPbPr inputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright