Operation, Starting up the projector | BenQ MX662 specs

Operation

Starting up the projector

1.Plug the power cord into the projector and into a

power outlet. Turn on the power outlet switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied.

Please use the original accessories (e.g. power cord) only with the device to avoid possible dangers such as electric shock and fire.

2.Press POWER to start the projector. As soon as the lamp lights up, a "Power On Ring Tone" will be heard. The POWER indicator light flashes green and stays green when the projector is on.

The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected.

(If necessary) Rotate the focus ring to adjust the image clearness.

To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 33 for details.

If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp.

3.If the projector is activated for the first time, select your OSD language following the on-screen instructions.

4.If you are prompted for a password, press the arrow keys to enter a six-digit password. See "Utilizing the password function" on page 22 for details.

5.Switch all of the connected equipment on.

6.The projector will start to search for input signals. The current input signal being scanned appears in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message “No Signal” will continue displaying until an input signal is found.

You can also press SOURCE on the projector or remote control to select your desired input signal. See "Switching input signal" on page 24 for details.

•If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message “Out of Range” displayed on the background screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See "Timing chart" on page 57 for details.

•If no signal is detected for 3 minutes, the projector automatically enters ECO BLANK mode.

18 Operation

Image 18

BenQ MX662 user manual Operation, Starting up the projector

Contents

MX662/MW663 Digital Projector Table of contents Important safety instructions Safety Instructions Safety Instructions 3000 m Feet Ceiling mounting the projector Projector features Introduction Shipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Remote control Remote control effective range Replacing the remote control batteries Front Table Positioning your projectorChoosing a location Front Ceiling MX662 Projection dimensionsObtaining a preferred projected image size Max length Offset Inch MW663 Connection Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Best Operation Starting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystone Using the menus Below is the overview of the OSD menu Setting a password Using a security cable lockUtilizing the password function If you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio MX662 MW663 Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature Setting a preferred color temperature 3D Color Management Setting the presentation timer Resetting current or all picture modesSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-Right Locking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environment Adjusting the sound level Adjusting the soundUsing the test pattern Turning off the Power On/Off Ring Tone Using the teaching templates To select Blackboard or Whiteboard Presenting from a USB Reader Direct power off Shutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Color Temperature Picture ModeTemperature Fine Tuning 3D Color Settings TimerInstallation Search Remote System Setup Basic menu Function DescriptionOperation Receiver Audio System Setup Advanced menu Function Description HighAltitude Lamp Standby System Setup Advanced menu Function DescriptionReset All Network Current SystemStatus Maintenance Care of the projector Lamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Status Message Replacing the lamp Resetting the lamp timer Use the handle to slowly pull the lamp out of the projector Maintenance Lamp events IndicatorsLight Status & Description Power events Thermal events Troubleshooting Specifications Projector specifications Dimensions Ceiling mount installation Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input KHz Pixel Supported timing for Component-YP bP r inputSupported timing for Video and S-Video inputs Timing Copyright Warranty and Copyright informationLimited warranty Disclaimer