6ADJUSTMENT INFORMATION FIG.3
6.1Adjusting the spray nozzle (for models with this feature) Water ow is adjusted by regulating the nozzle (E).
6.2Adjusting the detergent (on models with this feature) Detergent ow is adjusted using the regulator (F).
6.3Adjusting the detergent pressure
Set the adjustable nozzle on " 
" to deliver detergent at the correct pressure (on models with this feature).
6.4Adjusting the pressure (on models with this feature)
The regulator (G) is used to adjust the working pressure. The pres- sure is shown on the pressure gauge (where tted).
7INFORMATION ON USE OF THE APPLIANCE FIG.4
7.1Controls
- Starter device (H).
Set the starter switch on (ON/1) to:
a)start the motor (in models without AS device);
b)set the motor ready to start (in models with AS device).
If there is a pilot light on the starter device, it should light up. If the “low/high” settings are available, use them as follows: Low : low pressure washing
High : high pressure washing
Set the starter device switch on (OFF/0) to shut down the applian- ce.
If there is a pilot light on the starter device, it should go out.
-Water jet control lever (I).
Caution - Danger!
During operation the appliance must be positioned as shown in g. 4 on a sturdy, stable surface.
7.2Start-up
Caution - Danger!
Before starting up the appliance check that the water supply hose is connected properly; use of the appliance without water will damage it; do not cover the ventilation grilles when the appliance is in use.
1)Turn on the water supply tap fully.
2)Release the safety catch (D).
3)Depress the gun trigger for a few seconds and start up the appli- ance using the starter device (ON/1).
AS models - In AS models with automatic delivery ow
- When the gun trigger isreleased the dynamic pressure automati- cally cuts out the motor (see g.4);
- When the gun trigger is depressed the automatic drop in pres- sure starts the motor and the pressure is restored after a very slight delay;
- If the AS is to function correctly all gun releasing and depress- ing operations must be performed at intervals of less than
To prevent damage to the appliance, when running do not stop the water jet for more than 10 minutes at a time.
7.3Stopping the appliance
1)Set the starter device switch on (OFF/0).
2)Depress the gun trigger and discharge the residual pressure inside the hoses.
3)Engage the gun safety catch (D).
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| English |
| 19 |
| ||||
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
7.4Restarting
1)Release the safety catch (D).
2)Depress the gun trigger and discharge the residual air inside the hoses.
3)Set the starter device on (ON/1).
7.5Storage
1)Switch the appliance o (OFF/0).
2)Remove the plug from the socket.
3)Turn o the water supply tap.
4)Discharge the residual pressure from the gun until all the water has come out of the nozzle.
5)Drain the detergent tank.
6)Engage the gun safety catch (D).
7.6Relling and using detergent
When using detergent, the adjustable nozzle must be set on " 
" (on models with this feature).
Fill the tank with highly degradable detergent.
7.7Recommended cleaning procedure
Dissolve dirt by applying the detergent mixed with water to the surface while still dry.
When dealing with vertical surfaces work from the bottom upwards. Leave the detergent to act for
8MAINTENANCE FIG.5
Any maintenance operations not covered by this chapter should be carried out by an Authorized Sales and Service Centre.
Caution - Danger!
Always disconnect the plug from the power socket before carrying out any work on the appliance.
8.1Cleaning the nozzle
1)Disconnect the lance from the nozzle.
2)Remove any dirt deposits from the nozzle hole using the tool (C1).
8.2Cleaning the lter
Clean the suction lter (L) and the detergent lter after every 50 hours of operation.
8.3Unjamming the motor (on models with this feature)
In case of lengthy stoppages, limescale sediments may cause the motor to seize. To unjam the motor, turn the drive shaft with a tool (M).
8.4End-of-season storage
Treat the appliance with
