46
THISMACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.
Before connecting the machine to the power line, make sure the switch is in the “OFF” position and be sure that the
electric current is of the same characteristics as indicated on the machine. All line connections should make good
contact. Running on low voltage will damage the machine.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
1. All grounded,cord-connected machines:
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is
equipped with an electric cord having an equipment-
grounding conductor and a grounding plug. The plug
must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify the plug provided - if it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
Improperconnection of the equipment-grounding
conductor can resultin risk of electric shock. The
conductor with insulation having an outer surface that
is green with or without yellow stripes is the
MOTOR SPECIFICATIONSGROUNDING INSTRUCTIONS
ADVERTENCIA
ADVERTÊNCIA
WARNING
Sujete correctamente el
soporte. Ajuste los tornillos
antes de usar la herramienta. • Prenda
o suporte corretamente. Aperte os
parafusos antes de utilizar a
ferramenta • Properly secure
bracket. Tighten screw before use.
RADIACION LASER. NO MIRE FIJAMENTE
HACIA EL RAYO. PRODUCTO LASER DE
CLASE 2 • RADIAÇÃO DE LASER! NÃO OLHE
DIRETAMENTE AO FEIXE. LASER CLASSE 2
• LASER RADIATION. DO NOT STARE INTO
BEAM. CLASS 2 LASER PRODUCT.
187820-00
FOR LASER SAFETY OBSERVE THE FOLLOWING:
•LASERLIGHT - DO NOT STARE INTO BEAM, APERTURE,or into a reflection
from a mirror-like surface Fig. A & B.
•AVOID EXPOSURE - LASER LIGHT IS EMITTED FROMFRONT GUARD
APERTURE.Use of controls or adjustments, or performance of procedures
other than those specified herein may result in hazardous laser light exposure.
•DO NOT DISASSEMBLE LASER MODULE.The laser is a CLASS II LASER
PRODUCT that can emit laser power up to 1 mWMAX at 650 nm, which could
result in exposure with the moduledisassembled. The laser unit complies with
21 CFR 1040.10 and 1040.11.
•USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATIONEXPOSURE.
•THE USE OF OPTICAL INSTRUMENTSwith this product will increase eye
hazard.
•LASER RADIATION, avoid direct eye exposure, serious eye injury can result.
•DO NOT OPERATE IN EXPLOSIVE ATMOSPHERES, such as in the presence of
flammable liquids, gases, or dust.
•USE ONLY WITH THE SPECIFICALLY DESIGNATED BATTERIES.Use of any
other batteries may create a risk of fire.
•USE ONLY ACCESSORIES that are recommended by the manufacturer for your
model.
•ACCESSORIES THAT MAY BE SUITABLE FOR ONE LASER,may create a risk of
injury when used on another laser.
•REPAIRS AND SERVICING MUSTbe performed by a qualified repair facility.
Repairs performed by unqualified personnel could result in serious injury.
•DO NOT REMOVE OR DEFACE WARNING LABELS.Removing labels increases
the risk of exposure to radiation.
•THIS PRODUCT IS INTENDED for use in a temperature range of 41°F(5°C) -
104°F(40°C).
ADDITIONAL SAFETY RULES FOR THE LASER
Fig. B
Your machine is wired for: 220V ~ 50Hz (Argentina y Chile) 127V/220V ~ 60Hz (Brazil), 120V ~ 60Hz (CCA, Colombia
& México). Before connecting the machine to the power source, make sure the switch is in the “OFF” position.
Fig. A
equipment-grounding conductor. If repair or
replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor to
a live terminal.
Check with a qualified electrician or service personnel if
thegrounding instructionsare not completely
understood,or if in doubt as to whetherthe machine is
properly grounded.
Use only 3-wire extension cords that have 3-prong
grounding type plugs and matching 3-conductor
receptacles that accept the machine’s plug, as shown in
Fig. C. Repair or replace damaged or worn cord
immediately.
POWER CONNECTIONS
For your convenience and safety the
following labels are on your tool.