INSTALLATION - OPERATION - MAINTENANCE
IMPORTANT NOTES FOR INSTALLATION AND OPERATION
KLT-G Series
GAS FIRED TRI-LEG TILTING KETTLE
Intended for commercial use only. Not for household use
Do not attempt to operate this unit in the event of a power failure
This manual should be retained for future reference
DESCRIPTION
TABLE OF CONTENTS
PAGE
DIMENSIONS
1.0 SERVICE CONNECTIONS
MODEL
SIDES
2.0 INSTALLATION INSTALLATION CODES AND STANDARDS
0 INCHES
BACK
TO INSTALL
INSTALLATION Continued
2.0 INSTALLATION Continued GAS CONNECTION
ELECTRICAL CONNECTION
2.0 INSTALLATION Continued WATER CONNECTION
2.0 INSTALLATION Continued PERFORMANCE CHECK
GAS CONTROL INSTRUCTIONS
3.0 OPERATION
A. Lighting
COMPLETE SHUTDOWN
DAILY SHUTDOWN
GREEN IGNITION LIGHT
FRONT PANEL CONTROLS POWER SWITCH
RED COOKING LIGHT
AMBER LOW WATER LIGHT
THERMOSTAT
DIAL SETTING
PRESSURE GAUGE
SIGHT GLASS
DAILY OPERATION
PRESSURE RELIEF VALVE
END USE TIPS
1. Turn off when not in use 2. Limit preheat times
GAS SAVING TIPS
3. Use lid when possible 4. Maintain equipment
3.0 OPERATION Continued
4.0 CLEANING INSTRUCTIONS
DAIRY DRAW-OFF VALVE CLEANING
4.0 CLEANING INSTRUCTIONS Continued DRAW-OFF VALVE CLEANING
WHAT TO DO IF SURFACE RUST APPEARS
4.0 CLEANING INSTRUCTIONS Continued
STAINLESS STEEL
CAUTION Improper use of this procedure may damage your appliance
Soil and burn deposits which do not respond to the above procedure can usually be removed by rubbing the surface with SCOTCH-BRITE scouring pads or STAINLESS scouring pads. DO NOT USE ORDINARY STEEL WOOL as any particles left on the surface will rust and further spoil the appearance of the finish. NEVER USE A WIRE BRUSH, STEEL SCOURING PADS EXCEPT STAINLESS, SCRAPER, FILE OR OTHER STEEL TOOLS. Surfaces which are marred collect dirt more rapidly and become more difficult to clean. Marring also increases the possibility of corrosive attack. Refinishing may then be required
4.0 CLEANING INSTRUCTIONS Continued
Daily
5.0 MAINTENANCE
Monthly
Twice a Year minimum
ADJUSTMENTS
6.0 SERVICE GENERAL
Orifice Size
Natural
6.0 SERVICE Continued
PRESSURE SWITCH
THERMOSTAT
9. Replace the front panel when adjustment is complete
6.0 SERVICE Continued TO ADJUST PRESSURE SWITCH
ADDING WATER Low water light comes on
RE-ESTABLISHING VACUUM
LOOK FOR
7.0 TROUBLESHOOTING PROBLEM
Kettle Size/Gas Type
SHUTTER SETTINGS
Natural
Propane
Figure 1 Shutter setting at
MATERIAL SAFETY DATA SHEET
MATERIAL SAFETY DATA SHEET PREPARATION INFORMATION
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product
Effective Date 02/20/01, Date Printed 07/10/02, MSD
Product DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code
3. HAZARDS IDENTIFICATION EMERGENCY OVERVIEW
Product DOWFROST* HD HEAT TRANSFER FLUID, DYED
4. FIRST AID
Product Code Effective Date 02/20/01, Date Printed 07/10/02, MSD
5. FIRE FIGHTING MEASURES FLAMMABLE PROPERTIES
FLAMMABILITY LIMITS
Product DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code
MATERIAL SAFETY DATA SHEET
Effective Date 02/20/01, Date Printed 07/10/02, MSD
MEDIA TO BE AVOIDED Do not use direct water stream
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
7. HANDLING AND STORAGE
MATERIAL SAFETY DATA SHEET
Product DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code
10. STABILITY AND REACTIVITY
9. PHYSICAL AND CHEMICAL PROPERTIES
MATERIAL SAFETY DATA SHEET
Product DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code
Product DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code
MATERIAL SAFETY DATA SHEET
Effective Date 02/20/01, Date Printed 07/10/02, MSD
or R indicates a trademark of The Dow Chemical Company
MATERIAL SAFETY DATA SHEET
14. TRANSPORT INFORMATION
Product DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code
Effective Date 02/20/01, Date Printed 07/10/02, MSD
MATERIAL SAFETY DATA SHEET
Effective Date 02/20/01, Date Printed 07/10/02, MSD U.S. REGULATIONS
Product DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code
or R indicates a trademark of The Dow Chemical Company
16. OTHER INFORMATION
CANADIAN REGULATIONS
MATERIAL SAFETY DATA SHEET
Product DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code
