Manuals / Blodgett / Kitchen Appliance / Hot Beverage Maker

Blodgett KLT-G Series manual Physical And Chemical Properties, Stability And Reactivity

Models: KLT-G Series

1 38

Download 38 pages 38.84 Kb

Page 34

MATERIAL SAFETY DATA SHEET

Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED

Product Code: 04632

Effective Date: 02/20/01, Date Printed: 07/10/02, MSD: 002239

EXPOSURE GUIDELINES: Propylene glycol: AIHA WEEL is 50 ppm total, 10 mg/m3 aerosol only.

9.PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE/PHYSICAL STATE:	Clear yellow liquid.
ODOUR:	Odourless
VAPOUR PRESSURE:	0.22 mmHg @ 20EC
VAPOUR DENSITY:	2.6
BOILING POINT:	320EF, 160EC
SOLUBILITY IN WATER/MISCIBILITY:	Complete
SPECIFIC GRAVITY OR DENSITY:	1.058 @ 25/25EC

10.STABILITY AND REACTIVITY

CHEMICAL STABILITY: Thermally stable at typical use temperatures.

CONDITIONS TO AVOID: Avoid use temperatures above 450EF, 232EC. Product can degrade at elevated temperatures. Generation of gas during decomposition can cause pressure in closed systems.

INCOMPATIBILITY WITH OTHER MATERIALS: Avoid contact with oxidizing materials. Avoid contact with strong acids

HAZARDOUS DECOMPOSITION PRODUCTS: Hazardous decomposition products depend upon temperature, air supply and the presence of other materials.

HAZARDOUS POLYMERIZATION: Will not occur.

11.TOXICOLOGICAL INFORMATION (See Section 3 for Potential Health Effects. For detailed toxicological data, write or call the address or non-emergency number shown in Section 1).

SKIN: The LD50 for skin absorption in rabbits is >10,000 mg/kg.

* or (R) indicates a trademark of The Dow Chemical Company.

34

Image 34

Blodgett KLT-G Series manual Physical And Chemical Properties, Stability And Reactivity, Material Safety Data Sheet

Contents

KLT-G Series IMPORTANT NOTES FOR INSTALLATION AND OPERATIONINSTALLATION - OPERATION - MAINTENANCE GAS FIRED TRI-LEG TILTING KETTLEIntended for commercial use only. Not for household use Do not attempt to operate this unit in the event of a power failureThis manual should be retained for future reference DESCRIPTION TABLE OF CONTENTSPAGE DIMENSIONS 1.0 SERVICE CONNECTIONSMODEL 0 INCHES 2.0 INSTALLATION INSTALLATION CODES AND STANDARDSSIDES BACKINSTALLATION Continued TO INSTALL2.0 INSTALLATION Continued GAS CONNECTION 2.0 INSTALLATION Continued WATER CONNECTION ELECTRICAL CONNECTION2.0 INSTALLATION Continued PERFORMANCE CHECK GAS CONTROL INSTRUCTIONS 3.0 OPERATIONA. Lighting DAILY SHUTDOWN COMPLETE SHUTDOWNRED COOKING LIGHT FRONT PANEL CONTROLS POWER SWITCHGREEN IGNITION LIGHT AMBER LOW WATER LIGHTPRESSURE GAUGE DIAL SETTINGTHERMOSTAT SIGHT GLASSDAILY OPERATION PRESSURE RELIEF VALVEEND USE TIPS 3. Use lid when possible 4. Maintain equipment GAS SAVING TIPS1. Turn off when not in use 2. Limit preheat times 3.0 OPERATION Continued4.0 CLEANING INSTRUCTIONS 4.0 CLEANING INSTRUCTIONS Continued DRAW-OFF VALVE CLEANING DAIRY DRAW-OFF VALVE CLEANINGSTAINLESS STEEL 4.0 CLEANING INSTRUCTIONS ContinuedWHAT TO DO IF SURFACE RUST APPEARS CAUTION Improper use of this procedure may damage your appliance4.0 CLEANING INSTRUCTIONS Continued Soil and burn deposits which do not respond to the above procedure can usually be removed by rubbing the surface with SCOTCH-BRITE scouring pads or STAINLESS scouring pads. DO NOT USE ORDINARY STEEL WOOL as any particles left on the surface will rust and further spoil the appearance of the finish. NEVER USE A WIRE BRUSH, STEEL SCOURING PADS EXCEPT STAINLESS, SCRAPER, FILE OR OTHER STEEL TOOLS. Surfaces which are marred collect dirt more rapidly and become more difficult to clean. Marring also increases the possibility of corrosive attack. Refinishing may then be requiredMonthly 5.0 MAINTENANCEDaily Twice a Year minimumOrifice Size 6.0 SERVICE GENERALADJUSTMENTS Natural6.0 SERVICE Continued PRESSURE SWITCHTHERMOSTAT 6.0 SERVICE Continued TO ADJUST PRESSURE SWITCH 9. Replace the front panel when adjustment is completeADDING WATER Low water light comes on RE-ESTABLISHING VACUUM 7.0 TROUBLESHOOTING PROBLEM LOOK FORNatural SHUTTER SETTINGSKettle Size/Gas Type PropaneFigure 1 Shutter setting at 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION MATERIAL SAFETY DATA SHEET PREPARATION INFORMATIONMATERIAL SAFETY DATA SHEET Product3. HAZARDS IDENTIFICATION EMERGENCY OVERVIEW Product DOWFROST* HD HEAT TRANSFER FLUID, DYED Product CodeEffective Date 02/20/01, Date Printed 07/10/02, MSD Product DOWFROST* HD HEAT TRANSFER FLUID, DYED5. FIRE FIGHTING MEASURES FLAMMABLE PROPERTIES Product Code Effective Date 02/20/01, Date Printed 07/10/02, MSD4. FIRST AID FLAMMABILITY LIMITSEffective Date 02/20/01, Date Printed 07/10/02, MSD MATERIAL SAFETY DATA SHEETProduct DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code MEDIA TO BE AVOIDED Do not use direct water streamMATERIAL SAFETY DATA SHEET 7. HANDLING AND STORAGE8. EXPOSURE CONTROLS/PERSONAL PROTECTION Product DOWFROST* HD HEAT TRANSFER FLUID, DYED Product CodeMATERIAL SAFETY DATA SHEET 9. PHYSICAL AND CHEMICAL PROPERTIES10. STABILITY AND REACTIVITY Product DOWFROST* HD HEAT TRANSFER FLUID, DYED Product CodeEffective Date 02/20/01, Date Printed 07/10/02, MSD MATERIAL SAFETY DATA SHEETProduct DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code or R indicates a trademark of The Dow Chemical CompanyProduct DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code 14. TRANSPORT INFORMATIONMATERIAL SAFETY DATA SHEET Effective Date 02/20/01, Date Printed 07/10/02, MSDProduct DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code Effective Date 02/20/01, Date Printed 07/10/02, MSD U.S. REGULATIONSMATERIAL SAFETY DATA SHEET or R indicates a trademark of The Dow Chemical CompanyMATERIAL SAFETY DATA SHEET CANADIAN REGULATIONS16. OTHER INFORMATION Product DOWFROST* HD HEAT TRANSFER FLUID, DYED Product Code