CC408 Operators Guide 6. Disarming the System
EN 9
Arming in STAY Mode 2
Hold down the [0] button until two beeps sound. The STAY indicator lights and exit time starts counting.
Any zones programmed to be automatically isolated in STAY Mode 2 flash until exit time expires. At the end of exit time, all zones selected to be automatically isolated extinguish and the codepad provides one short beep.
5.4Programming STAY Mode 2 Zones
You can only program zones to be automatically isolated in STAY Mode 2 if you have a Master Code.
How to Program STAY Mode 2 Zones
1.Enter your
[2 5 8 0 4 #]). Three beeps sound and the STAY indicator flashes.
2.Enter the zone number to be automatically isolated, followed by the [*] key (for example, [1 *] = Zone 1, [2 *] = Zone 2).
The selected zone flashes. If you make a mistake, enter the same zone number followed by the [#] key to clear the incorrect zone.
To select additional zones to be automatically isolated in STAY Mode 2, repeat Step 2 as many times as required.
3.To exit this mode, press the [#] key when you have selected all zones to be automatically isolated in STAY Mode 2. Two beeps sound and the STAY and AWAY indicators turn dark.
6.Disarming the System
When you enter the premises after the system is armed in AWAY Mode, or if you have armed the system in STAY Mode 1 or STAY Mode 2, you must disarm the system before entry time expires to disable detection devices that activate an alarm. Only your installer can program the entry time.
If there was an alarm condition prior to disarming the system, a flashing zone indicator displays indicating a previous alarm on that zone.
How to Disarm the System
Enter your user code followed by the [#] key (for example, [2 5 8 0 #]). Two beeps sound.
7.User Codes
7.1Adding User Codes
Only the Master Code holder can add or change other system user codes, including the Master Code. Up to eight user codes can be programmed to operate the system.
How to Add a User Code
1.Enter your
2.Enter the user code number (1 to 8) followed by the [#] key (for example, [2 #] = User 2, [8 #] = User 8). Two beeps sound and the selected user number displays on the codepad indicators.
3.Enter the digits required for the new code followed by the [#] key (for example, for user code 5768, enter [5 7 6 8 #]). Two beeps sound and the STAY and AWAY indicators turn dark. To add or change other user codes, repeat this procedure as many times as required.
7.2Adding Radio Remote User Codes
Only the Master Code holder can add or change other system user codes, including the Master Code. Up to eight radio user codes (User Codes 9 to 16) can be programmed to operate the system.
How to Add a Radio Remote User Code
1.Enter your
[2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY indicators flash.
2.Enter the radio remote user code number (9 to 16), followed by the [#] key (for example, [9 #] = User 9, [1 6 #] = User 16). Two beeps sound and the selected user number displays on the codepad indicators.
3.Press any button on the keyfob so the system learns the ID number. Two beeps sound and the STAY and AWAY indicators extinguish.
To add or change other radio remote user codes, repeat this procedure as many times as required.
7.3Deleting User Codes/Radio User Codes
Only the Master Code holder can delete other system user codes.
How to Delete a User Code
1.Enter your
[2 5 8 0 1 #]).
Three beeps sound and the STAY and AWAY indicators flash.
2.Enter the user code number (User Code 1 to 8, Radio User Code 9 to 16), followed by the [#] key (for example, [2 #] = User 2, [1 6 #] = User 16). Two beeps sound and the selected user number displays on the codepad indicators.
3.Press the [*] key to delete the selected user code. Two beeps sound and the STAY and AWAY indicators turn dark. To delete other user codes, repeat this procedure as many times as required.
