LTC 4600 Series Instruction Manual Replacement Parts

EN 16

 

 

4.9LTC 4637 Series Rack-mount Card Cage

4.9.1Installation

1.Install the LTC 4637 Series Rack-mount into a standard EIA 19in. rack, using user-supplied rack- mounting hardware. Be careful to not damage exposed objects on the back of the card cage unit.

2.If a secondary earth ground connection is needed, a grounded wire with a ground lug can be attached to the rack using the protruding screw provided on the right side of the chassis.

3.Connect the supplied AC voltage line cord between the rear of the power supply and the appropriate AC voltage source.

4.Fiber optic plug-in modules can be installed into any of the available 14 slots of the card cage. Most modules require only a single slot width, but others, such as the LTC 4644 and LTC 4645 Series, require two slot widths.

5.If desired, LTC 4600/00 blank panels (ordered separately) may be installed to cover unused slots. A single blank panel covers a single slot opening.

6.Refer to the sections of this manual for specific installation instructions regarding the plug-in modules.

4.9.2Indicators

1.LTC 4637 Series front panel LED illuminates when AC power is applied to the unit.

2.Each fiber optic plug-in module is equipped with a POWER LED indicator that illuminates when power is applied to the rack unit.

LTC 4637/60

power supply

Power

BOSCH

Figure 11 LTC 4637 Series Typical Installation

4.9.3LTC 4637 Maintenance / Service Information

1.The power supply is fused with a 1A slow blow fuse. To replace the fuse, remove the AC power line cord from the power supply, and carefully pry out the fuse module above the AC connector.

2.The 3-pin connector on the rack supplies a 20VAC center tapped voltage, and is the only electrical connection from the back plane to a plug-in module. Each plug-in module contains its own fuse, so in the unlikely event of a module failure, the other modules in the rack remain unaffected.

3.The power supply is modular in construction, and can be replaced in the event of damage or failure. To remove the power supply from the rack:

a)Disconnect the AC line cord and power supply cable from the circuit board back plane, located on the rear of the card cage.

b)Loosen the four (4) screws located at the front of the power supply using a small flat blade screwdriver. Slide the power supply out of

the card cage.

c)Reverse the above procedure to install the power supply into the card cage.

5REPLACEMENT PARTS

UPA-1509-60 Power Supply for 120VAC Stand- alone Modules

UPA-1509-50 Power Supply for 230VAC Stand- alone Modules

Bosch Security Systems July 08, 2008

Page 15 Page 17
Page 16
Image 16
Bosch Appliances LTC 4600 instruction manual Replacement Parts, LTC 4637 Series Rack-mount Card Cage
Page 15 Page 17

LTC 4600 specifications

The Bosch Appliances LTC 4600 is an impressive addition to any modern kitchen, delivering a perfect blend of efficiency, innovation, and style. This versatile appliance is specifically designed for those who appreciate high-quality performance and cutting-edge technology in their food preparation processes.

One of the standout features of the LTC 4600 is its spacious cooking capacity. With ample room to prepare meals for families or dinner parties, the appliance supports various cooking methods, making it perfect for multi-course meals. Its intelligently designed interior ensures even heat distribution, resulting in perfectly cooked dishes every time.

Equipped with advanced cooking technologies, the LTC 4600 incorporates Bosch’s exclusive EcoSilence Drive motor. This brushless motor operates quietly and efficiently, minimizing energy consumption while maximizing performance. Energy efficiency is further enhanced by the appliance’s integrated sensors, which monitor cooking progress and adjust the heat settings accordingly.

The user-friendly interface of the LTC 4600 is another notable aspect. Its intuitive control panel features easy-to-read LCD displays, allowing users to select cooking modes, adjust temperatures, and set timers with minimal effort. Additionally, the appliance is equipped with smart connectivity options, enabling users to control and monitor cooking processes remotely via a smartphone app.

Safety is a top priority in the design of the LTC 4600. The appliance includes an auto shut-off feature, which activates after a designated period of inactivity, ensuring peace of mind for busy home cooks. Moreover, the appliance utilizes durable materials that resist wear and tarnish, ensuring longevity and reliable performance.

Cleaning up after cooking can be a hassle, but Bosch has made this easier with the LTC 4600’s self-cleaning feature. This technology allows users to enjoy effortless maintenance, saving time and effort after preparing delicious meals.

In summary, the Bosch Appliances LTC 4600 is a top choice for those seeking a reliable and sophisticated kitchen companion. With its spacious design, advanced cooking technologies, user-friendly interface, and enhanced safety features, this appliance is sure to meet the demands of any modern kitchen. Whether you're an avid cook or someone who simply enjoys preparing meals for loved ones, the LTC 4600 promises to elevate your culinary experience.
Top Page Image Contents