figure 8 to calculate the minimum gauge of cable required.

Existing drywall construction (retrofit)

Mark the centre position of the speaker and position the template so the mark shows through the hole in the middle.

Trace round the outer edge of the template and cut neatly just inside the line.

To improve the mechanical integrity of the ceiling and reduce the likelihood of rattles, we recommend you apply a bead of wood glue or mastic along the joints between the back of the plasterboard and the studs in the vicinity of the speaker.

Run the cable to the aperture, allowing enough length to comfortably connect the speaker, but not too much, as the excess may rattle against the structure.

New drywall construction

The speaker can be installed once the ceiling is completed in the same manner as retrofitting, but it is easier to position and cut the hole if the optional pre-mount kit is used before the plasterboard (sheetrock) is fitted.

Staple or nail the PMK to the studs as described in the instructions with the kit. Run the cable and secure it to the PMK. Allow enough length to comfortably connect the speaker, but not too much, as the excess may rattle against the structure.

Results are affected by how well the plasterboard is attached to the studs and we recommend gluing as well as screwing or nailing the panels to the studs in the vicinity of the speaker.

Once the board is fitted, the inner flange of the PMK serves as a guide for a hole router or saw.

Damping the cavity

Drape fibreglass or mineral wool matting at the back of the ceiling board, covering the aperture and extending at least 30cm (1 ft) around the speaker into open void.

(figure 7)

IMPORTANT: Ensure that the materials you use meet local fire and safety regulations.

Fitting the speaker

All connections should be made with the equipment switched off.

Connect the cables, observing the correct polarity.

With the grille removed, position the speaker in the aperture and screw in the 4 screws visible from the front. These screws automatically swing out clamping dogs that locate behind the mounting surface. Ensure that they have located properly before fully tightening the screws. A certain amount of flexing of the frame is allowed to take up unevenness in the mounting surface, but do not overtighten the screws as excessive distortion of the speaker frame may result.

Customising

The frame has a paintable white semi-matte finish, ready if necessary to be re-finished to match your own decor. Fit the paint mask before re-finishing. Do not re-finish the drive units or baffle area behind the grille. Avoid touching the drive units, as damage may result.

Before painting the grille, peel off the fabric scrim from the back, otherwise the pores will get clogged and the sound will be impaired. If the scrim does not stay in place properly when replaced, spray the back of the grille mesh (NOT the scrim) with a light coating of 3M SprayMount adhesive or similar.

Français

Garantie limitée

Cher Client,

Bienvenue à B&W.

Ce produit a été conçu et fabriqué en vertu des normes de qualité les plus rigoureuses. Toutefois, en cas de problème, B&W Loudspeakers et ses distributeurs nationaux garantissent une main d’œuvre (exclusions possibles) et des pièces de rechange gratuites dans tout pays desservi par un distributeur agréé de B&W.

Cette garantie limitée est valide pour une période de cinq ans à compter de la date d’achat ou une période de deux ans pour les composants électroniques, y compris les haut-parleurs amplifiés.

Conditions

1La garantie est limitée à la réparation de l’équipement. Les frais de transport ou autres, les risques associés à l’enlèvement, au transport et à l’installation des produits ne sont pas couverts par cette garantie.

2La garantie est exclusivement réservée au propriétaire d’origine et ne peut pas être transférée.

3Cette garantie ne s’applique qu’aux produits faisant l’objet de vices de matériaux et/ou de construction au moment de l’achat et ne sera pas applicable dans les cas suivants :

a.détériorations entraînées par une installation, connexion ou un emballage incorrect,

b.détériorations entraînées par un usage autre que l’usage correct décrit dans le manuel de l’utilisateur, la négligence, des modifications ou l’usage de pièces qui ne sont pas fabriquées ou agréées par B&W,

c.détériorations entraînées par un équipement auxiliaire défectueux ou qui ne convient pas,

d.détériorations résultant de : accidents, foudre, eau, chaleur, guerre, troubles de l’ordre public ou autre cause ne relevant pas du contrôle raisonnable de B&W ou de ses distributeurs agréés,

e.les produits dont le numéro de série a été modifié, effacé, éliminé ou rendu illisible,

f.les produits qui ont été réparés ou modifiés par une personne non autorisée.

4Cette garantie vient en complément à toute obligation juridique nationale / régionale des revendeurs ou distributeurs nationaux et n’affecte pas vos droits statutaires en tant que client.

Comment faire une réclamation en vertu de la garantie

Veuillez respecter la procédure ci-dessous, si vous souhaitez faire une réclamation sous garantie :

3

Page 5 Page 7
Page 6
Image 6
Bowers & Wilkins CCM616 owner manual Français, Garantie limitée
Page 5 Page 7

CCM616 specifications

The Bowers & Wilkins CCM616 is an exceptional in-ceiling loudspeaker that exemplifies high-quality audio engineering and innovative design. This speaker is part of Bowers & Wilkins' renowned CCM series, which is designed for both residential and commercial applications, providing a seamless way to enjoy premium sound while maintaining aesthetic integrity.

One of the standout features of the CCM616 is its impressive sound quality, which is attributed to its 6-inch composite woofer and a 1-inch aluminum dome tweeter. This combination ensures a wide frequency response, allowing it to handle both deep bass and crisp highs with remarkable clarity. The tweeter is also equipped with a unique FST (Fixed Suspension Transducer) design, which helps to minimize distortion and provides a more natural sound reproduction.

The CCM616 is built with versatility in mind. It is designed to be easily installed into ceilings, making it an ideal choice for home theaters, living rooms, and even commercial spaces such as restaurants or conference rooms. The speaker's low-profile design allows it to blend seamlessly into the ceiling, while the paintable grille offers additional customization options, so it can match the decor of any environment.

For enhanced performance, the CCM616 features a built-in back box, which aids in reducing sound leakage and improving the overall acoustic performance. This technology enhances the speaker's bass response and provides a more focused sound stage, making it suitable for critical listening situations.

Another key characteristic is the speaker’s use of proprietary technologies, such as the advanced drive units and high-quality crossover network. These elements work together to ensure that the audio signal is transmitted efficiently, maintaining the integrity of the sound across different volume levels.

In terms of installation, the CCM616 features easy-to-use mounting clamps that provide a secure fit in various ceiling types. This straightforward installation process is coupled with a user-friendly design, allowing both professional installers and DIY enthusiasts to achieve excellent results.

Overall, the Bowers & Wilkins CCM616 stands out as a top-tier in-ceiling speaker, combining sophisticated technology with aesthetic design. Its superior audio performance, versatile installation options, and elegant appearance make it an ideal choice for those seeking an immersive sound experience without compromising on style. Whether for personal or commercial use, the CCM616 is engineered to deliver exceptional audio enjoyment in any setting.
Top Page Image Contents