potable water. Unions should be installed on both the hot and cold water lines for future servicing and disconnection of the water heater. Install a shut-off valve in the cold water supply line.

2.In order to service the water heater in the event the heat exchanger needs to be flushed of mineral deposits, tee fittings with shut-off valves and service connections to hoses should be installed. Also, install a shut-off valve to the hot water supply to isolate the service tee fittings. A plumbing installation kit, which includes these fittings and a pressure relief valve, is available from your supplier. Refer to the piping diagrams in Section IV, “Water Connections”.

3.Install a pressure relief valve on a tee connection from the hot water outlet piping from the water heater. Refer to the piping diagrams (Figure 6 and Figure 7) and pressure relief valve warning in Section IV, “Water Connections.”

4.In cold climates, where piping can freeze during an extended power failure, drain solenoid valves should be installed on the cold and hot water supply lines to allow water to drain from the water heater when power is interrupted. Refer to the piping diagram (Figure 8) “Recommended Piping for Power Failure Freeze Protection” in Section IV, and contact your Bradford White dealer if assistance is needed.

5.If this water heater is installed in a closed water supply system, such as the one having a back- flow preventer in the cold water supply, provisions must be made to control thermal expansion. DO NOT operate this water heater in a closed system without provisions for controlling thermal expansion. Warranties do not cover damages from thermal expansions, such as pressure bulges and/or deformities. Your water supplier or local plumbing inspector should be contacted on how to control this situation.

6.Purge the cold water line prior to connecting to the water heater to remove debris. Debris will clog the mesh strainer of the inlet filter. The inlet strainer prevents debris from damaging the flow sensor or clogging the coil. It may need to be cleaned periodically and should be cleaned after the initial operation. DO NOT operate the water heater without the filter in place. In areas where sediment may be periodically present in the water supply, a Y-type strainer (#20 mesh) or cartridge filter should be installed on the cold water inlet to the water heater to prevent the water heater fine mesh strainer from getting plugged and restricting water flow.

7.After installation of the water lines, open the main water supply valve and fill the water heater. While the water heater is filling, open several hot water faucets to allow air to escape from the water system. When a steady stream of water flows through the faucets, close them and check all water connections for possible leaks.

8.This water heater may also be connected to a circulating pump or storage tank for increased flow capacity during high demand periods.

9.Commercial installations may require more than one water heater piped together in a manifold to supply enough capacity for high temperature and high water flow applications. Special controls are available from your Bradford White supplier for operating more than one water heater together. These controls stage the operation of the water heaters for the flow rates and control the amount of flow through each water heater. Order p/n MSA-2M for the electronic manifold control for the first and second water heater and p/n MSA-2S for the wiring harness for each additional water heater to be controlled. A maximum of (5) water heaters can be connected together. Alternatively, to connect only (2) water heaters, an EZConnectTM harness, p/n REU- EZC-1US, can be used. Instructions are included with these parts.

NOTICE

Take care when using pipe dope or thread sealing tape to avoid clogging the inlet screen and water flow sensor. Wipe off excess pipe dope from threads before connecting to the water heater.

Commercial dishwashers will require either more than one water heater, or a storage tank to supply a sufficient volume of hot water.

18

Page 17 Page 19
Page 18
Image 18
Bradford-White Corp TGHE-199E-N(X), TGHE-160E-N(X) instruction manual
Page 17 Page 19

TGHE-160E-N(X), TGHE-199E-N(X) specifications

Bradford-White Corporation is renowned for its commitment to quality and innovation in the water heating industry. Among its extensive range of products, the TGHE-199E-N(X) and TGHE-160E-N(X) models stand out for their advanced technology and reliable performance, making them a preferred choice for both residential and commercial applications.

The TGHE-199E-N(X) and TGHE-160E-N(X) are high-efficiency, gas-fired water heaters designed to meet the rising demand for sustainable energy solutions without compromising on performance. Both models feature a powerful, energy-efficient design that significantly reduces energy consumption while providing a consistent supply of hot water.

One of the main features of these models is their use of advanced technology in water heating. The units are equipped with a high-efficiency burner and an optimized heat exchanger that maximizes the transfer of energy, ensuring rapid heating and minimal standby loss. This efficiency is further enhanced by their ability to modulate gas flow, allowing the heater to adjust its operation based on actual demand, rather than running at full capacity at all times.

Safety is a priority in the design of the TGHE-199E-N(X) and TGHE-160E-N(X). Both models are equipped with an electronic ignition system, which eliminates the need for a continuous pilot light, reducing gas consumption and enhancing safety. Furthermore, they include advanced venting options, such as concentric or PVC venting, providing installation flexibility while adhering to stringent building codes.

Moreover, these water heaters are built to last, featuring a durable tank design with a powder-coated, steel construction and a patented Vitraglas® lining. This lining protects against corrosion and extends the life of the tank, ensuring long-term performance and reliability.

Installation and maintenance of the TGHE-199E-N(X) and TGHE-160E-N(X) are straightforward, thanks to their user-friendly design. They come with easily accessible components, making service and repairs less time-consuming and more cost-effective.

In summary, the Bradford-White TGHE-199E-N(X) and TGHE-160E-N(X) gas-fired water heaters exemplify the best in modern water heating technology. Their energy efficiency, safety features, and durable construction make them a top choice for those seeking dependable hot water solutions in residential and commercial settings. With a commitment to innovation and quality, Bradford-White continues to lead the way in delivering superior water heating products.
Top Page Image Contents