Combination Water and Space Heating Applications – Commercial Use Water Heaters Only

Commercial use water heaters may be used for space heating or combination space heating/potable water heating applications, provided the following requirements and recommended piping diagrams are carefully followed.

WARNING

The following instructions must be carefully followed to assure safe and reliable operation of the water heater. All piping components connected to this water heater must be suitable for use with potable water. In Massachusetts, space heating piping length must not exceed 50 feet. Toxic chemicals, such as those used for boiler treatment, must not be introduced into potable water used for space heating. This water heater must not be connected to an existing heating system or component(s) previously used with a non-potable water heating appliance. When the system requires water for space heating at temperatures higher than required for other means, an ASSE approved mixing valve must be installed to temper the water for those uses in order to reduce the scald hazard potential.

1.Only commercial use water heaters may be used for combination water heating/space heating applications. Residential use water heaters will not be covered under warranty for water heating/space heating applications.

2.The temperature setting of the water heater thermostat must not exceed 160°F.

3.In combination space heating/potable water heating applications that require higher water temperatures than normally used for potable water uses, an ASSE approved thermostatic mixing valve must be installed to temper the water for those uses in order to reduce the scald hazard potential.

4.In order to assure adequate flow through the water heater, follow the recommended piping diagram and circulator specifications (see Figure 9).

5.An expansion tank will be required in all space heating applications.

6.A Y-type mesh strainer (#20 mesh screen) should be installed on the cold water inlet of the water heater to prevent clogging of the fine mesh screen on the water heater cold water inlet connection.

7.A water softener must be used if the water supply has a tested hardness level above 10 grains of hardness.

8.All piping must be ¾” copper or larger.

9.All components must be suitable for use with potable water.

10.The water heater should be located as close as practical to the space heating heat exchanger.

11.A check valve should be located after the circulator(s) to prevent backflow during potable water demands.

12.A heat exchanger may be required to separate the potable water from the space heating circuit in certain applications.

24

Page 23 Page 25
Page 24
Image 24
Bradford-White Corp TGHE-199E-N(X), TGHE-160E-N(X) instruction manual
Page 23 Page 25

TGHE-160E-N(X), TGHE-199E-N(X) specifications

Bradford-White Corporation is renowned for its commitment to quality and innovation in the water heating industry. Among its extensive range of products, the TGHE-199E-N(X) and TGHE-160E-N(X) models stand out for their advanced technology and reliable performance, making them a preferred choice for both residential and commercial applications.

The TGHE-199E-N(X) and TGHE-160E-N(X) are high-efficiency, gas-fired water heaters designed to meet the rising demand for sustainable energy solutions without compromising on performance. Both models feature a powerful, energy-efficient design that significantly reduces energy consumption while providing a consistent supply of hot water.

One of the main features of these models is their use of advanced technology in water heating. The units are equipped with a high-efficiency burner and an optimized heat exchanger that maximizes the transfer of energy, ensuring rapid heating and minimal standby loss. This efficiency is further enhanced by their ability to modulate gas flow, allowing the heater to adjust its operation based on actual demand, rather than running at full capacity at all times.

Safety is a priority in the design of the TGHE-199E-N(X) and TGHE-160E-N(X). Both models are equipped with an electronic ignition system, which eliminates the need for a continuous pilot light, reducing gas consumption and enhancing safety. Furthermore, they include advanced venting options, such as concentric or PVC venting, providing installation flexibility while adhering to stringent building codes.

Moreover, these water heaters are built to last, featuring a durable tank design with a powder-coated, steel construction and a patented Vitraglas® lining. This lining protects against corrosion and extends the life of the tank, ensuring long-term performance and reliability.

Installation and maintenance of the TGHE-199E-N(X) and TGHE-160E-N(X) are straightforward, thanks to their user-friendly design. They come with easily accessible components, making service and repairs less time-consuming and more cost-effective.

In summary, the Bradford-White TGHE-199E-N(X) and TGHE-160E-N(X) gas-fired water heaters exemplify the best in modern water heating technology. Their energy efficiency, safety features, and durable construction make them a top choice for those seeking dependable hot water solutions in residential and commercial settings. With a commitment to innovation and quality, Bradford-White continues to lead the way in delivering superior water heating products.
Top Page Image Contents