LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing

property damage, personal injury or loss of life.

A. This water heater does not have a

∙

Immediately call your gas supplier from a

 

pilot. It is equipped with a direct

 

neighbor’s phone. Follow the gas supplier’s

 

ignition device, which automatically

 

instructions.

 

lights the burner. Do not try to light

∙

If you cannot reach your gas supplier, call the fire

 

the burner by hand.

 

department.

B.

BEFORE OPERATING: Smell all

C.

Use only your hand to operate the remote control

 

around the appliance area for gas.

 

keypad. Never use tools. If the remote keypad

 

Be sure to smell next to the floor,

 

doesn’t work, do not try to repair it, call a qualified

 

because some gas is heavier than

 

service technician. Forced or improper repair

 

air and will settle on the floor.

 

may result in a fire or explosion.

WHAT TO DO IF YOU SMELL GAS

D.

Do not use this water heater if any part has been

∙

Do not try to light any appliance.

 

under water. Immediately call a qualified service

∙

Do not touch any electric switch; do

 

technician to inspect the water heater and to

 

not use any phone in your building.

 

replace any part of the control system and any

 

 

 

gas control which has been under water.

OPERATION INSTRUCTIONS

1.STOP! Read the safety information above before proceeding.

2.Set the thermostat to the lowest setting.

3.Turn off all power to the electrical appliance.

4.This water heater does not have a pilot. It is equipped with a direct ignition device, which automatically lights the burner. Do not try to light the burner by hand.

5.Turn the manual valve located at the gas inlet of the appliance clockwise to “OFF” (See Figure 15).

6.Wait (5) minutes to clear out any gas. If you then smell gas, STOP! Follow “B” in the safety information above on this label. If you don’t smell gas, go to next step.

7.Turn the manual valve located at the gas inlet of

appliance counterclockwise to “ON” (See Figure 15).

8.Turn on all electric power to the appliance.

9.Set the thermostat to desired setting.

10.If the appliance will not operate, Follow the instructions “To Turn Off Gas To Appliance” and call your service technician or gas supplier.

TO TURN OFF GAS TO THE APPLIANCE

1.Set the thermostat to the lowest setting.

2.Turn off all electric power to the appliance if service is to be performed.

3.Turn the manual valve at gas inlet of appliance

clockwise to “OFF” (See Figure 15).

Figure 15. Manual Gas Valve.

40

Page 39 Page 41
Page 40
Image 40
Bradford-White Corp TGHE-199E-N(X) Lighting Instructions For Your Safety Read Before Operating, Operation Instructions
Page 39 Page 41

TGHE-160E-N(X), TGHE-199E-N(X) specifications

Bradford-White Corporation is renowned for its commitment to quality and innovation in the water heating industry. Among its extensive range of products, the TGHE-199E-N(X) and TGHE-160E-N(X) models stand out for their advanced technology and reliable performance, making them a preferred choice for both residential and commercial applications.

The TGHE-199E-N(X) and TGHE-160E-N(X) are high-efficiency, gas-fired water heaters designed to meet the rising demand for sustainable energy solutions without compromising on performance. Both models feature a powerful, energy-efficient design that significantly reduces energy consumption while providing a consistent supply of hot water.

One of the main features of these models is their use of advanced technology in water heating. The units are equipped with a high-efficiency burner and an optimized heat exchanger that maximizes the transfer of energy, ensuring rapid heating and minimal standby loss. This efficiency is further enhanced by their ability to modulate gas flow, allowing the heater to adjust its operation based on actual demand, rather than running at full capacity at all times.

Safety is a priority in the design of the TGHE-199E-N(X) and TGHE-160E-N(X). Both models are equipped with an electronic ignition system, which eliminates the need for a continuous pilot light, reducing gas consumption and enhancing safety. Furthermore, they include advanced venting options, such as concentric or PVC venting, providing installation flexibility while adhering to stringent building codes.

Moreover, these water heaters are built to last, featuring a durable tank design with a powder-coated, steel construction and a patented Vitraglas® lining. This lining protects against corrosion and extends the life of the tank, ensuring long-term performance and reliability.

Installation and maintenance of the TGHE-199E-N(X) and TGHE-160E-N(X) are straightforward, thanks to their user-friendly design. They come with easily accessible components, making service and repairs less time-consuming and more cost-effective.

In summary, the Bradford-White TGHE-199E-N(X) and TGHE-160E-N(X) gas-fired water heaters exemplify the best in modern water heating technology. Their energy efficiency, safety features, and durable construction make them a top choice for those seeking dependable hot water solutions in residential and commercial settings. With a commitment to innovation and quality, Bradford-White continues to lead the way in delivering superior water heating products.
Top Page Image Contents