Installation InstructionsAerada 1000 Series Gooseneck Faucet
Installation Instructions - Single Hole and Cover Plate
1 | Remove the locknut (1), washer |
|
|
| 2 | Install faucet assembly |
|
|
|
(2), stilt washer (3) from the |
|
| 4 | into deck hole. |
|
|
| ||
| spout shank (4). Remove shank |
|
|
| Use plumbers putty |
|
|
| |
|
|
|
|
|
|
|
| ||
| from cover plate (if supplied). |
|
|
|
| to seal faucet to deck. |
|
|
|
|
|
|
| 3 |
| Be careful not to |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| 2 |
| nick or cut the |
|
|
|
|
|
|
|
| sensor cable during |
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| installation. |
|
|
|
|
|
|
| 1 |
|
|
|
|
|
| Install stilt washer (1) all |
|
|
| 4 | Install the shank washer (1) |
|
|
|
3 the way up onto shank, |
|
|
| and locknut (2) onto faucet |
|
|
| ||
| crown side up. Position |
|
|
|
| shank. Tighten locknut |
|
|
|
| sensor cable (2) through |
|
|
|
| securely to prevent collar and |
|
|
|
| one of the rounded slots | 1 |
|
|
| spout from rotating. If |
|
|
|
| in the stilt washer (1). |
|
|
| necessary, support spout base |
|
|
| |
|
|
|
|
|
| from above to prevent twisting. |
|
|
|
| 2 |
|
|
|
|
|
|
| 1 |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| 2 |
| If faucet was installed with |
|
|
| 6 | Install spout nut (1) onto the |
|
|
|
5 cover plate, secure cover plate |
|
|
| spout. |
|
|
| ||
| with basin washers (1), flat |
|
|
|
|
|
|
|
|
| washers (2) and locknuts (3). |
|
|
|
| For swivel mount, only install |
|
|
|
|
|
|
|
|
| two plastic split washers (2). | 1 |
|
|
|
|
|
|
|
|
|
|
| |
| 1 |
|
|
|
| For rigid mount, only install |
|
|
|
| 2 |
|
|
|
| 2 |
|
| |
|
|
|
|
|
| 1/8" thick plastic washer (3). |
|
| |
|
|
|
|
|
|
|
|
| |
| 3 |
|
|
|
| Mount the spout completely |
| 3 |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| into the base and securely |
|
|
|
|
|
|
|
|
| tighten the spout nut (1). |
|
|
|
7a | CAUTION: Flush water lines |
|
| 7b | IMPORTANT: Flow rates exceeding the |
| |||
before beginning this step. |
|
|
| 0.5 GPM maximum limit for public |
|
| |||
Attach the outlet assembly (1) and aerator |
|
|
| lavatories set by ASME A112.18.1 |
|
| |||
|
|
| negate the UPC certification of this |
| |||||
gasket (2) to the spout. The outlet assembly |
|
|
| faucet for public use applications. |
|
| |||
is equipped from the factory with a 0.5 GPM |
|
|
| For applications requiring laminar |
|
| |||
cartridge (white screen). To configure the |
|
|
|
|
| ||||
2 |
|
| flow without an aerator, refer to the |
| |||||
outlet with the 2.2 GPM cartridge (yellow |
|
| 1 | ||||||
|
|
| instructions below. |
|
| ||||
screen) refer to step 8. |
|
|
|
|
|
| |||
|
|
| Attach the plain spray ring (1) to the spout. Insert |
| |||||
|
|
|
|
|
|
| |||
| IMPORTANT: If 0.5 GPM spout is to |
|
| the laminar flow control insert (2) into the spout. |
|
|
| ||
|
|
|
|
|
|
|
| ||
| be used, skip Step 8 and proceed | 1 |
| IMPORTANT: If laminar flow is to be used, |
| 2 | |||
| directly to Installation - Solenoid |
|
| ||||||
|
|
| skip Step 8 and proceed directly to |
|
| ||||
| and Optional Valves, page 4. |
|
|
|
| ||||
|
|
| Solenoid and Optional Valves, page 4. |
|
|
| |||
|
|
|
|
|
|
|
| ||
8
IMPORTANT: Flow rates exceeding the 0.5 GPM maximum limit for public lavatories set by ASME A112.18.1 negate the UPC certification of this faucet for public use applications.
To convert outlet assembly to 2.2 GPM:
1.Disassemble outlet assembly using key (1).
2.Remove the 0.5 GPM cartridge (white screen) and replace it with the 2.2 GPM cartridge (2).
3.Install the rubber washer (3), adapter (4) and aerator gasket (5).
IMPORTANT: Proceed directly to Installation - Solenoid and Optional Valves, page 4.
5
4
3 
2 
1 
Bradley Corporation • | 9/23/04 | 3 |
