Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 32494
Maintenance and Lubrication
Maintenance and Lubrication Schedule
| Lubrication Diagram |
Parallel Arm | |
(Tower Pivot Points - 2) | |
Pivot Pins (8) | LO |
LO | |
| Spring (2 springs - 4 Points) |
| LO |
| Parallel Arm |
| Pivot Pins (8) |
| LO |
Proper maintenance is necessary to ensure safe, troublefree operation. Inspecting the lift for any wear, damage or other abnormal conditions should be a part of a regular service program. Simple inspections can detect potential problems.
The maintenance and lubrication procedures speci- fied in this schedule must be performed by a Braun authorized service representative at the scheduled intervals according to the number of cycles.
Braun dual parallel arm lifts are equipped with hard- ened pins and
When servicing the lift at the recommended inter-
intervals following the scheduled “4500 Cycles” maintenance. These intervals are a general guideline for scheduling maintenance procedures and will vary according to lift use and conditions. Lifts exposed to severe conditions (weather, envi- ronment, contamination, heavy usage, etc.) may require inspection and maintenance procedures to be performed more often than specified.
WARNING
Maintenance and lubrication procedures must be performed as specified by an autho- rized service techni- cian. Failure to do so may result in serious bodily injury and/or property damage.
Switch Arm Pivot Pins (2)
LO
vals, inspection and lubrication procedures specified in the previous sections should be repeated. Clean the components and the surrounding area before applying lubricants. LPS2 General Purpose Penetrating Oil is recommended where Light Oil is called out. Use of improper lubricants can attract
Maintenance Indicator: The Lift Ready green LED mounted on top of the pump cover will begin to blink after every 750 cycles. The blinking LED will not affect the functions of the lift, but is a reminder to complete necessary maintenance and lubrication.
UHMW Bearing (4)
DE
Rotating Pivot
Slide Arm Pivot Pins
LO
Inboard
Platform
Platform Fold Axles (2) 
LO
Platform Pivot Pin (2 Points)
LO
Inboard Locator
Pivot Points
LO
Outer Platform Pivot Pins (2)
LO
Outer Barrier Activation
Foot Pivot Point (2)
LO
Outboard |
Platform |
dirt or other contaminants which could result in wear or damage to the components. Platform compo- nents exposed to contaminants when lowered to the ground may require extra attention.
Lift components requiring grease are lubricated dur- ing assembly procedures. When these components are replaced, grease must be applied during instal- lation procedures. Specified lubricants are available from The Braun Corporation (part numbers provided above).
All listed inspection, lubrication and maintenance procedures should be repeated at “750 cycle”
Once the lift has been serviced, fully stow the lift. Once stowed, press the UP button on the hand pendant and the Floor Level Set button on the back side of the pump cover until the Lift Ready green LED stops blinking.
Discontinue lift use immediately if maintenance and lubrication procedures are not properly performed, or if there is any sign of wear, damage or improper operation. Contact your sales representative or call The Braun Corporation at
Outer barrier hinge pivot points (2) | Apply Light Oil - See Lubrication Diagram |
Platform Fold Link Roller/Pin (4)
LO
| Outer Barrier |
Outer Barrier Hinge Pivot Points | Arm Slots (2) |
LO | |
(2) and |
|
Outboard Platform Pivot Pins (2) |
|
LO |
|
See the Maintenance/Lubrication Schedule for recommended applications per number of cycles.
|
|
|
| |
| Specified (recommended) | Available | Braun | |
Lubricant | Type | Lubricant | Amount | Part No. |
LO - Light Oil | Light Penetrating Oil | LPS2, General Purpose | 11 oz. | 15807 |
| (30 weight or equivalent) | Penetrating Oil | Aerosol Can |
|
DE - | Stainless Stick | 1.68 oz. | 15806 | |
| Style (tube) | Stick (tube) |
|
|
LG - Light Grease | Light Grease | Lubriplate | 14 oz. | 15805 |
| (Multipurpose) |
| Can |
|
| Outer barrier arm slots (2) | Apply Light Oil - See Lubrication Diagram | |
| Outboard platform pivot pins (2) | Apply Light Oil - See Lubrication Diagram | |
| Outer barrier activation foot pivot pins (2) | Apply Light Oil - See Lubrication Diagram | |
750 | Platform fold link rollers and pins (4 sets) | Apply Light Oil - See Lubrication Diagram | |
Outer platform pivot pins (2) | Apply Light Oil - See Lubrication Diagram | ||
Cycles | |||
|
| ||
| Apply Light Oil - See Lubrication Diagram | ||
| Apply Light Oil - See Lubrication Diagram | ||
| points (2 springs - 4 points) |
| |
| Inspect | Resecure, replace defective parts or otherwise | |
| or damage (bent, deformed or misaligned), posi- | correct as needed. Note: Apply Light Grease to | |
| tive securement (external snap rings) and proper | ||
| operation |
|
