Breville BKC600XL/BKC700XL manual One-time priming process

Operating your breville gourmet single cup brewer™

Operating your breville gourmet single cup brewer™

8.Set the date dial on the Upper Filter Holder 2 months ahead. This will remind you when the Charcoal Filter will need to be replaced.

9.Place the assembled Filter Holder into the Water Tank, aligning so the date dial is visible from outside the Tank. Push down hard on the assembled Filter Holder until it snaps into place.

10.Your Brewer is ready for the one-time priming process.

NOTE:

Replace the Water Filter every

2 months, or 60 tank refills, more if you have hard water.

To order replacement Water Filters, visit www.breville.com.

We recommend removing the Water Filter if you choose not to replace the Water Filter every 2 months, as the filter may clog and affect the smell and taste of the water.

One-time priming process

Priming fills the internal tank with water and cleanses the brewing system. You cannot use your Brewer until it has been primed for its first use.

NOTE:

If the Brewer has been exposed to temperatures below freezing, allow the Brewer at least two hours to reach room temperature before priming. A frozen or extremely cold Brewer will not prime properly and can cause damage.

1.Unwrap the power cord and plug the Brewer into a grounded outlet.

2.Place a 12 oz. mug on the Drip Tray Plate. The drip tray plate and drip tray can be removed to accomodate taller mugs and travel mugs.

3.Fill the Water Tank with water up to the 'MAX' mark on the viewing window.

The Water Tank can be filled in two ways:

a)Remove the Water Tank Lid and pour water directly into the Water Tank while it is still attached to the Brewer, then replace the Lid.

b)Remove the Water Tank Lid, then gripping the handle located on the left side of the Water Tank, lift upwards. Fill with water. Place the Water Tank back onto the Brewer and replace the Lid.

NOTE:

Do not use water that has been treated by a 'water softener'. The increase in sodium levels in the water can cause scaling in the brewer and hinder its performance.

4.Press and release the Power Switch located on the lower back, right side of the Brewer. The Power Switch is spring loaded and will return to its original position.

NOTE:

For BKC600XL priming information, please refer to page 30.

5.The Water Tank LED and LCD screen will illuminate. The Brewer will automatically fill with water and make a quiet vibrating sound. This is normal. The LCD screen will indicate 'HEATING'.

NOTE:

If the Water Tank is empty or not in place on the Brewer, the Water Tank LED’s will flash and the LCD screen will indicate ‘REFILL TANK’. None of the control panel buttons will be active until water is added to the Water Tank.

6.Once the water is heated, the LCD screen will indicate 'OPEN HEAD'. Open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely. Do not insert a K-Cup®during this process. This will allow you to run a cleansing brew. The 'BREW' button will now be illuminated.

7.Press the 'BREW' button. This will start a cleansing brew which will complete the priming sequence. Hot water will flow into your mug. When the water flow stops, discard the hot water.

NOTE:

The Brewer will take about 4 minutes to heat up during the priming process.

8.The LCD screen will indicate ‘HEATING’ as the Brewer heats the water for the next brew cycle. Once the water is heated, the LCD screen may indicate ‘REFILL TANK’.

9.Fill the Water Tank with water up to the 'MAX' mark on the viewing window.

10.The LCD screen will indicate ‘OPEN HEAD’. Open the Brewing Chamber Head by raising and lowering the Safety Locking Arm completely. The LCD screen will indicate ‘READY TO BREW’.

11.The one-time priming process is now complete and you are ready for your first K-Cup®brew (page 12) or My K-Cup®brew (page 14).

10 11