INSTALLATION

WIRE CONNECTIONS

Recommended Torque Values

Torque all wire connections/fasteners to values recommended in Figure 10. Suitable for copper wire of 60°/75°C rating.

Figure 10 — Recommended Torque Values

CONNECTIONS:

Torque Value

 

 

In Main Distribution Panel:

 

Refer to panel manufacturer specs

 

 

 

In Disconnect Box:

 

 

 

240V AC Utility

5 in-lb

 

 

Engine Start

5 in-lb

 

 

Remote Status

5 in-lb

 

 

Generator

17 in-lb

 

 

Ground

40 in-lb

 

 

Circuit Breakers:

 

Refer to circuit breaker manufacturer specs

 

 

 

Generator AC Connection System

A single-phase, three-wire AC connection system is used in the Home Standby Generator. The stator assembly consists of a pair of stationary windings with two leads brought out of each winding. The junction of leads 22 and 33 forms the neutral lead. A complete schematic and wiring diagram can be found on pages 26-27.

NOTE: Neutral is not bonded to ground at generator.

Grounding the Generator

Ground the Home Generator System per applicable codes, standards, and regulations. The GND lug is located in the disconnect box.

Generator Control Circuit Connection

Control circuit interconnections consist of "240V AC Utility" leads. These two leads must be routed in conduit. Control lead functions are briefly described as follows:

Leads deliver utility power to generator’s circuit board, oil warmer, optional battery warmer and charge the battery.

Using installer-supplied minimum 300V, 14 AWG copper wire, connect control circuit terminals in the disconnect box to the Transfer Switch.

Remote Diagnostic LED Plate

The light on the remote LED plate is referred to as the Diagnostic LED. The LED will stay lit indicating the generator is in ready mode and will turn on and off in a series of blinks if certain faults are detected in the Home Standby Generator. A mounting plate is supplied so that it can be installed at a convenient indoor location. The owner will use it to observe the status of the Home Standby Generator. Consult with the owner for a convenient location.

To install the remote diagnostic LED plate:

Mount installer-supplied electrical box to wall.

Using installer-supplied wire, connect the remote LED leads to the “Remote Status Light” in disconnect box.

NOTE: LED leads are polarity sensitive.

• Attach mounting plate to electrical box.

Refer to the section Fault Detection System for operation.

BEFORE INITIAL START-UP

Engine Oil

This engine is shipped from the factory filled with the recommended oil. Before starting the engine, check oil level and ensure that engine is serviced as described in the engine operator’s manual.

NOTICE

Any attempt to crank or start the engine before it has been properly serviced with the recommended oil will result in equipment failure.

Refer to engine manual for oil fill information.

Damage to equipment resulting from failure to follow this instruction will void warranty.

Oil Considerations

Your Home Standby Generator is equipped with an engine that has been pre-run at the factory and does not require the traditional “break-in” procedure.

The generator is filled with synthetic oil (API SJ/CF 5W- 30W). This allows for generator operation in the widest range of temperature and climate conditions.

NOTE: The use of synthetic oil DOES NOT alter the required oil change intervals described in the engine operator’s manual.

17

Page 17
Image 17
Briggs & Stratton 040220A manual Wire Connections, Before Initial START-UP

040220A specifications

Briggs & Stratton is renowned for its high-performance engines, and the Briggs & Stratton 040220A is no exception. This powerful engine is designed to deliver reliable performance for a variety of outdoor applications, including lawn mowers, garden tractors, and other small machinery. One of the standout features of the 040220A is its sturdy construction. It is built with high-quality materials, ensuring durability and longevity, even under demanding conditions.

The 040220A is equipped with an overhead valve (OHV) design, which enhances engine efficiency and provides better fuel economy. This technology allows for improved airflow and better combustion, resulting in increased power output while reducing emissions. With its advanced engineering, the engine is capable of delivering consistent performance across a range of applications, making it a versatile choice for both residential and commercial users.

Another important characteristic of the 040220A is its easy starting system. Designed for user convenience, this engine features a user-friendly recoil start mechanism that ensures reliable ignition with minimal effort. This is particularly beneficial for users who value time efficiency and want to avoid the hassle of complicated starting procedures.

The 040220A also boasts impressive torque and horsepower ratings, which contribute to its ability to handle tough tasks with ease. This engine is designed to provide ample power for heavy-duty cutting, mulching, and other demanding applications, ensuring that users can complete their work efficiently.

In addition to its power and performance, the Briggs & Stratton 040220A is also designed with user maintenance in mind. It features easy-access oil fill and drain ports, making routine maintenance tasks straightforward. This attention to user convenience helps ensure that owners can keep their engines in optimal working condition with minimal effort.

Overall, the Briggs & Stratton 040220A stands out as a reliable and powerful engine that incorporates advanced technologies and features aimed at enhancing performance and ease of use. Its robust design, efficient operation, and commitment to user convenience make it an excellent choice for anyone in need of a dependable engine for their outdoor power equipment. Whether you're a DIY enthusiast or a professional landscaper, the 040220A is engineered to meet your needs with proven performance and reliability.