INSTALLATION

OWNER ORIENTATION

This section provides the Home Standby Generator owner with the information necessary to achieve the most satisfactory and cost effective installation possible.

The illustrations are for typical circumstances and are meant to familiarize you with the installation options available with the Home Standby Generator. A thorough understanding of these options will provide fundamental control over the cost of installation, as well as ensure final satisfaction and security.

Federal and local codes, appearance, noise levels, fuel types, and distances are the factors that must be considered when negotiating with an installation professional. As the distance from the existing electrical service and gaseous fuel supply increases, so must the piping and wiring materials. This is necessary to comply with local codes, overcome electrical voltage drops and gaseous fuel pressure drops.

Power Decrease at High Altitude or High Temperature

Air density is less at high altitudes, resulting in less available engine power. Specifically, engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and 1% for each 10° F (5.6°C) above 77°F (25°C). Make sure you and your installer consider these factors when determining total generator load.

INSTALLATION PROCEDURES

Unpacking Precautions

The unit is shipped bolted to its mounting pad, ready for installation. Avoid damage from dropping, bumping, collision, etc. Store and unpack carton with the proper side up, as noted on the shipping carton.

The factors mentioned above will have a direct affect on the overall price of your Home Standby Generator installation.

NOTE: In some areas you may need to acquire electrical permits for installing the Home Standby Generator, building permits for installing gas lines, and permits for noise allowances. Your installer should check your local codes AND obtain the permits before installing the generator.

Fuel Factors

An important consideration affecting the entire installation is the type of fuel used by your Home Standby Generator. The generator was factory tested and adjusted using natural gas as a fuel. liquid propane vapor (LP) may also be used as fuel by installing the included conversion kit.

For proper generator performance, the following fuel guidelines are recommended:

In engines set up to run on liquid propane vapor (LP), commercial grade HD5 propane with a minimum fuel energy of 2500 BTUs/ft³ with maximum propylene content of 5% and butane and heavier gas content of 2.5% and minimum propane content of 90%.

WARNING

Propane and Natural Gas are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

The Home Generator System is equipped with an automatic safety gas “fuel shut-off” valve.

DO NOT operate the equipment if the “fuel shut-off” valve is missing or inoperative.

Delivery Inspection

After removing the carton, carefully inspect the Home Standby Generator for any damage that may have occurred during shipment.

IMPORTANT: If loss or damage is noted at time of delivery, have the person(s) making delivery note all damage on the freight bill and affix his signature under the consignor's memo of loss or damage. If loss or damage is noted after delivery, separate the damaged materials and contact the carrier for claim procedures. Missing or damaged parts are not warranted.

Approved Transfer Switches

The Home Standby Generator should be used ONLY with Briggs & Stratton Power Products UL approved Transfer Switches. Connection to any other transfer switch will void your generator warranty.

Shipment Contents

The Home Standby Generator is supplied with:

Home Standby Generator w/disconnect box

Pre-attached mounting pad

One flexible hook-up hose (meets UL 569 and CSA 8.3)

Installation, start-up and operator’s manual

Installation checklist

Remote diagnostic LED plate

Oil drain tray

Touch-up paint

One spare 15A fuse

LP conversion kit

Roof hardware bag

9

Page 9
Image 9
Briggs & Stratton 040220A manual Owner Orientation, Installation Procedures

040220A specifications

Briggs & Stratton is renowned for its high-performance engines, and the Briggs & Stratton 040220A is no exception. This powerful engine is designed to deliver reliable performance for a variety of outdoor applications, including lawn mowers, garden tractors, and other small machinery. One of the standout features of the 040220A is its sturdy construction. It is built with high-quality materials, ensuring durability and longevity, even under demanding conditions.

The 040220A is equipped with an overhead valve (OHV) design, which enhances engine efficiency and provides better fuel economy. This technology allows for improved airflow and better combustion, resulting in increased power output while reducing emissions. With its advanced engineering, the engine is capable of delivering consistent performance across a range of applications, making it a versatile choice for both residential and commercial users.

Another important characteristic of the 040220A is its easy starting system. Designed for user convenience, this engine features a user-friendly recoil start mechanism that ensures reliable ignition with minimal effort. This is particularly beneficial for users who value time efficiency and want to avoid the hassle of complicated starting procedures.

The 040220A also boasts impressive torque and horsepower ratings, which contribute to its ability to handle tough tasks with ease. This engine is designed to provide ample power for heavy-duty cutting, mulching, and other demanding applications, ensuring that users can complete their work efficiently.

In addition to its power and performance, the Briggs & Stratton 040220A is also designed with user maintenance in mind. It features easy-access oil fill and drain ports, making routine maintenance tasks straightforward. This attention to user convenience helps ensure that owners can keep their engines in optimal working condition with minimal effort.

Overall, the Briggs & Stratton 040220A stands out as a reliable and powerful engine that incorporates advanced technologies and features aimed at enhancing performance and ease of use. Its robust design, efficient operation, and commitment to user convenience make it an excellent choice for anyone in need of a dependable engine for their outdoor power equipment. Whether you're a DIY enthusiast or a professional landscaper, the 040220A is engineered to meet your needs with proven performance and reliability.