Operation

Starting the Engine

IMPORTANT: Always unplug the battery float charger before starting the generator.

Disconnect all electrical loads from the generator. Use the following start instructions:

1. Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate the unit on a level surface will cause the unit not to start or shut down during operation.

2.Turn the fuel valve to the “On” position. The fuel valve handle should be vertical (pointing toward the ground) for fuel to flow.

3. Push choke lever to “Choke” position ( ).

4. Push engine rocker switch to “On”.

5A. For electric starting, push and hold the start button in start position until generator starts. To prolong the life of starter components, DO NOT hold start switch in start position for more than 15 seconds, and pause for at least 1 minute between starting attempts.

If engine starts, proceed to step 7.

If engine fails to start, proceed to step 6.

NOTE: If battery is discharged, use manual starting instructions.

5B. For manual starting, grasp recoil handle and pull slowly until slight resistance is felt. Then pull rapidly one time only to start engine.

WARNING

Starter cord kickback (rapid retraction) can result in bodily injury. Kickback will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains could result.

When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

NEVER start or stop engine with electrical devices plugged in and turned on.

If engine starts, proceed to step 7.

If engine fails to start, proceed to step 6.

6.Move choke lever to “Half” choke position, and pull recoil handle twice.

If engine fails to start, repeat steps 5 thru 7.

7.Slowly move choke lever to “Run” position ( ). If engine falters, move choke lever to “Half” choke position until engine runs smoothly, and then to “Run” position ( ).

IMPORTANT: If engine floods, place choke lever in “Run” position ( ) and crank until engine starts.

NOTE: If engine starts after 3 pulls but fails to run, or if unit shuts down during operation, make sure unit is on a level surface and check for proper oil level in crankcase. This unit may be equipped with a low oil protection device. If so, oil must be at proper level for engine to start.

WARNING

Contact with muffler area can result in serious burns.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

DO NOT touch hot parts and AVOID hot exhaust gases.

Allow equipment to cool before touching.

Keep at least 5 feet (1.5 m) of clearance on all sides of generator including overhead.

Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

12

BRIGGSandSTRATTON.COM

Page 12
Image 12
Briggs & Stratton 206405GS manual Operation, Starting the Engine

206405GS specifications

The Briggs & Stratton 206405GS is a powerful and reliable small engine designed for a wide range of applications, particularly in lawn care equipment, generators, and various outdoor power tools. Known for its innovative engineering and robust performance, this engine has garnered attention from both commercial and residential users alike.

One of the standout features of the 206405GS is its advanced overhead valve (OHV) design. This configuration enhances fuel efficiency and improves airflow into the combustion chamber, resulting in better overall performance. The engine's ability to deliver higher torque at lower RPMs makes it ideal for tasks requiring consistent power, such as mowing or tilling.

The Briggs & Stratton 206405GS is equipped with a 206cc displacement, offering a potent power output that can handle challenging yard work. With its easy starting mechanism, users can get their equipment up and running with minimal effort. The inclusion of a recoil starter ensures dependability, even in cold weather conditions.

Another notable characteristic of this engine is its durable construction. It features a heavy-duty, cast iron sleeve for added protection and longevity, allowing it to withstand the rigors of outdoor use. Additionally, the engine’s compact size makes it easy to integrate into various machines, facilitating its widespread adoption in the market.

The 206405GS also benefits from Briggs & Stratton’s exclusive technologies such as ReadyStart®. This system eliminates the need for manual priming, allowing for effortless starting every time. The engine’s built-in oil alert system is another important feature that automatically shuts down the engine in the event of low oil levels, protecting the engine from potential damage.

Maintenance is straightforward, with easy access to the air filter and spark plug, aiding in user convenience and minimizing downtime. The engine's fuel system is optimized for minimal maintenance while still delivering adequate power and efficiency.

In summary, the Briggs & Stratton 206405GS is a well-engineered small engine that combines power, efficiency, and durability. With its advanced features and robust performance, it serves as an ideal solution for various outdoor applications, catering to the needs of homeowners and professionals alike. Its reputation for reliability ensures that it continues to be a popular choice in the competitive market of small engines.