2650 PSI Pressure Washer

9.Engage trigger lock to spray gun trigger (Figure 10).

Figure 10 — Spray Gun with Trigger Lock Engaged

NOTE: Always keep the throttle lever in the “Fast” position when operating the pressure washer.

Trigger Lock

10.When starting engine, position yourself as recommended in Figure 11 and start engine according to instructions given in engine operator’s manual.Also see operating instructions tag located on the pressure washer.

Figure 11 - Recommended Starting Position

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

•ALWAYS point gun in safe direction and squeeze spray gun trigger, to release pressure and avoid kickback each time, before starting engine.

•When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

•After each starting attempt, where engine fails to run, always point gun in safe direction and squeeze spray gun trigger to release high pressure.

•Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when gun kicks back.

WARNING

Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

•DO NOT touch hot surfaces and avoid hot exhaust gases.

•Allow equipment to cool before touching.

•Keep at least 5 ft. (152 cm) clearance on all sides of pressure washer including overhead.

•Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

How to Stop Your Pressure Washer

1.Let engine idle for two minutes.

2.Turn engine off according to instructions given in engine operator’s manual.

3.ALWAYS point gun in a safe direction and squeeze spray gun trigger to release retained high water pressure.

IMPORTANT: Spray gun traps high water pressure, even when engine is stopped and water is disconnected.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.

Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury.

•Keep high pressure hose connected to pump and spray gun while system is pressurized.

•ALWAYS point gun in safe direction and squeeze spray gun trigger, to release high pressure, every time you stop engine. Engage trigger lock when not in use.

4.Engage trigger lock on spray gun when not in use.

11

Page 10 Page 12
Page 11
Image 11
Briggs & Stratton 2650 PSI manual How to Stop Your Pressure Washer, Trigger Lock
Page 10 Page 12

2650 PSI specifications

The Briggs & Stratton 2650 PSI pressure washer is a powerful and efficient cleaning machine designed for homeowners and professionals alike. Known for its sturdy build and reliable performance, this pressure washer offers an impressive combination of features that make it a must-have for tackling a variety of cleaning tasks around the home or job site.

One of the key features of the Briggs & Stratton 2650 PSI pressure washer is its powerful 3.0 GPM (gallons per minute) pump. This pump is designed to generate a maximum pressure of 2650 PSI, making it effective for removing dirt, grime, and tough stains from surfaces such as driveways, patios, decks, and vehicles. The high pressure combined with the flow rate ensures that users can complete their cleaning tasks efficiently and in less time compared to traditional cleaning methods.

Equipped with a reliable Briggs & Stratton engine, this pressure washer provides dependable starting and consistent performance over time. The engine is designed to minimize fuel consumption while maximizing power output, ensuring that users can work without frequent interruptions for refueling. Additionally, the engine features an easy-to-use recoil start system, making it user-friendly for individuals of all skill levels.

The pressure washer comes with a versatile accessory kit that includes multiple nozzles for varying pressure settings— ranging from low-pressure settings for delicate surfaces to high-pressure settings for tough jobs. This adaptability allows users to tackle different types of cleaning tasks without the need for multiple machines.

Another notable aspect of the Briggs & Stratton 2650 PSI pressure washer is its lightweight and portable design. The pressure washer is mounted on a sturdy frame with large wheels, making it easy to maneuver around a yard or driveway. The integrated handle ensures easy transportation, while the compact size allows for convenient storage when not in use.

In terms of durability, the pressure washer features a corrosion-resistant frame and components that withstand the rigors of outdoor use. This ensures longevity, allowing users to make the most of their investment.

Overall, the Briggs & Stratton 2650 PSI pressure washer blends power, efficiency, and durability. Whether you are maintaining your home or tackling larger cleaning projects, this machine provides excellent performance, making it a valuable tool for both homeowners and professionals.
Top Page Image Contents