HOUSING MOUNTED TO “I” JOIST
Requires additional framing for mounting tabs.
Discharge 900 to joists.
Additional framing must be a 2x6 (minimum height), at

FAN/LIGHT COMBINATION VENTILATOR / VENTILADORE CON LÁMPARA MODEL / MODELO 683L

READ AND SAVETHESE

INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURYTO PERSONS, OBSERVETHE FOLLOWING:

1.Use this unit only in the manner intended by the manufac- turer.If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2.Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the ser- vice disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3.Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.

4.Sufficient air is needed for proper combustion and ex- hausting of gases through the flue (chimney) of fuel burn- ing equipment to prevent backdrafting. Follow the heat- ing equipment manufacturer’s guideline and safety stan- dards such as those published by the National Fire Pro- tection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5.When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6.Ducted fans must always be vented to the outdoors.

7.If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit.

8.Never place a switch where it can be reached from a tub or shower.

9.This unit must be grounded.

CAUTION !

1.For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

2.This product is designed for ceiling installation only. This product is designed for installation in ceilings up to a 12/12 pitch. Ductwork must point up. DO NOT MOUNT THIS PRODUCT IN A WALL.

3.To avoid motor bearing damage and noisy and/ or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

4.Please read specification label on product for further information and requirements.

Installer: Leave this manual with the homeowner.

Homeowner: Use and Care information on page 4.

TYPICAL INSTALLATIONS

POWER CABLE

MOUNTING TABS

CEILING

JOIST

HOUSING

CEILING

MATERIAL GRILLE

HOUSING MOUNTED DIRECTLY TO JOIST

2x6 (or larger)

Discharge parallel to joists.

POWER CABLE

ADDITIONAL

*

MOUNTING

FRAMING

 

TABS

 

 

 

2 x 4

 

2 x 4

CEILING

CEILING

JOIST or

JOIST or

TRUSS

TRUSS

HOUSING

 

 

 

CEILING

MATERIAL GRILLE

HOUSING MOUNTEDTO 2x4TRUSS

Requires additional framing for mounting tabs.

Discharge parallel to joists.

POWER CABLE

ADDITIONAL

 

FRAMING

*

MOUNTING

 

 

 

 

TABS

 

 

 

 

HOUSING

 

"I"

CEILING

 

"I"

JOIST

 

JOIST

MATERIAL

GRILLE

 

 

HOUSING MOUNTED TO “I” JOIST

Requires additional framing for mounting tabs.

Discharge parallel to joists.

 

4" ROUND

POWER CABLE

DUCT

 

MOUNTING TABS

HOUSING

CEILING

 

ADDITIONAL

CEILING

MATERIAL

GRILLE

FRAMING*

JOIST

HOUSING MOUNTED TO ADDITIONAL FRAMING

Discharge 900 to joists.

 

4" ROUND

POWER CABLE

DUCT

 

MOUNTING TABS

HOUSING

2 x 4

 

 

ADDITIONAL

2 x 4

CEILING

 

FRAMING

 

CEILING

GRILLE

* CEILING

MATERIAL

 

JOIST or

 

 

 

 

JOIST or

TRUSS

 

 

 

 

TRUSS

HOUSING MOUNTED TO 2x4 TRUSS

Requires additional framing for mounting tabs.

Discharge 900 to joists.

 

4" ROUND

POWER CABLE

DUCT

MOUNTING TABS

 

HOUSING

 

 

 

"I"

 

 

ADDITIONAL

"I"

CEILING

GRILLE

FRAMING

*

JOIST

JOIST

MATERIAL

 

 

 

LEAY CONSERVE ESTAS

INSTRUCCIONES

ADVERTENCIA

PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O LESIONES PERSONALES, OBSERVE LO SIGUIENTE:

1.Utilice esta unidad solamente de acuerdo con las instrucciones del fabricante. Si tiene preguntas comuníquese con el fabricante a la dirección o al número telefónico que se indica en la garantía.

2.Antes de dar servicio o limpiar la unidad, interrumpa el suministro de energía en el panel de servicio y bloquee los dispositivos de desconexión para evitar la reinstalación accidental de la energía. Cuando no se puedan bloquear los dispositivos de desconexión, fije seguramente en el panel de servicio un medio de advertencia que sea vis- ible, como por ejemplo una etiqueta.

3.Una persona o personas calificadas deben realizar el trabajo de instalación y el cableado eléctrico, de acuerdo con todos los códigos y normas aplicables, inclusive los códigos y normas de construcción para evitar incendios.

4.Se necesita suficiente aire para que se realice la combustión y la descarga de gases adecuadas a través de la chimenea del equipo para quemar combustible a fin de evitar las corrientes de inversión. Observe los lineamientos del fabricante del equipo de calefacción y las normas de seguridad, como por ejemplo las publicadas por la Asociación Nacional de Protección contra Incendios (Na- tional Fire Protection Association: NFPA), y la Sociedad Americana de Ingenieros en Calefacción, Refrigeración y Sistemas de Acondicionamiento de Aire (American Society for Heating, Refrigeration and Air Conditioning Engineers: ASHRAE), y los códigos locales.ditioning Engineers (ASHRAE), and the local code authorities.

5.Cuando corte o perfore la pared o el cielo raso, tenga cuidado de no dañar el cableado eléctrico ni otras conexiones de servicios que se encuentren ocultas.

6.Los ventiladores con conductos siempre deben tener salida hacia el exterior.

7.Si se va a instalar esta unidad sobre una tina o ducha, debe marcarse que es apropiada para esta aplicación y conectarse a un GFCI (interruptor accionado por pérdida de conexión a tierra) en un circuito de derivación protegido.

8.Nunca coloque el interruptor en un lugar en donde se pueda alcanzar desde la tina o ducha.

9.Esta unidad debe conectarse a tierra.

PRECAUCIÓN !

1.Esta unidad debe usarse solamente para ventilación gen- eral.No la utilice para la descarga de materiales ni vapores peligrosos o explosivos.

2.Este producto está diseñado solamente para instalarse en el cielo raso. Este producto está diseñado para instalarse en cielos rasos con una pendiente de hasta 12/ 12. El sistema de conductos debe apuntar hacia arriba.

NO MONTE ESTE PRODUCTO EN LA PARED.

3.Para evitar causar daño a los cojinetes del motor y pistones impulsores ruidosos y/o no balanceados, mantenga los aerosoles para pirca, el polvo de construcción, etc. lejos del motor.

4.Por favor consulte la información y los requerimientos adicionales contenidos en la etiqueta de especificaciones que se encuentra en el producto.

A la persona que realiza la instalación: Deje este manual con el dueño de la casa.

Al dueño de la casa: Las instrucciones de operación y limpieza se encuentran en la página 4.

*

least 9-inches long.

Page 1 Page 2
Page 1
Image 1
Broan 683L warranty Advertencia, Precaución, Housing Mounted Directly to Joist, Housing Mounted to I Joist
Page 1 Page 2

683L specifications

The Broan 683L is a versatile and efficient ventilation fan designed to enhance indoor air quality while ensuring quiet and unobtrusive operation. This model stands out as a perfect blend of functionality, advanced technology, and sleek design, making it an ideal addition to bathrooms and other small spaces that require adequate ventilation.

One of the primary features of the Broan 683L is its powerful yet quiet performance. Equipped with a robust motor, this ventilation fan operates at an airflow capacity of 70 CFM, effectively circulating air to eliminate moisture and odors. This is particularly beneficial in bathroom settings, where humidity can lead to mold and mildew growth. The fan boasts a sound level of just 1.5 sones, ensuring a peaceful environment without the disruptive noise often associated with traditional ventilation systems.

The design of the Broan 683L features a low-profile, compact housing that allows for easy installation in various ceiling types. It is compatible with existing 4-inch ductwork, simplifying the installation process, especially in renovations. The attractive white polymeric grille provides a clean, modern aesthetic that fits seamlessly into any decor.

Technology is at the forefront of the Broan 683L, which incorporates innovative ventilation solutions. The fan includes a built-in exhaust damper that prevents backdrafts and helps maintain energy efficiency. Additionally, the fan can be connected to humidity sensing controls for automatic operation, ensuring that it only runs when needed. This feature greatly enhances convenience while reducing energy consumption.

Moreover, the Broan 683L is designed for durability and ease of maintenance. The durable motor is engineered for long-lasting performance, and the grille can be easily removed for cleaning purposes, promoting hygiene and optimal airflow over time.

In summary, the Broan 683L is an excellent choice for those seeking a reliable, efficient, and quiet ventilation solution. Its combination of powerful airflow, low noise levels, user-friendly design, and advanced technology makes it a standout option for enhancing indoor air quality in any small space. Whether you're renovating an existing bathroom or constructing a new one, the Broan 683L promises to deliver the ventilation needs with style and efficiency.
Top Page Image Contents