Broan 418, EC62 SERIES Use And Care, Operation, Don’t, Avoid when choosing a detergent, Filters

21. USE AND CARE

Filters

The filters should be cleaned frequently. Use a warm detergent solution. Wash more often if your cooking style generates more grease — like frying foods or wok cooking.

Remove filters by pushing it towards the back of power pack and rotating filter downward. Filters are dishwasher safe. Allow filters to dry completely before reinstalling them in the power pack.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the filters may occur if using phosphate detergent or as a result of local water conditions — but this will not affect filter performance. This discoloration is not covered by the warranty.

Blower(s) Cleaning

Remove the filters in order to access the blower(s). Vacuum blower(s) to clean. Do not immerse in water.

Power Pack Cleaning

Stainless steel cleaning:

Do:			Don’t:
•	Regularly wash with clean cloth or rag soaked with warm		•	Use any steel or stainless steel wool or any other scrapers
				to remove stubborn dirt.
	water and mild soap or liquid dish detergent.
			•	Use any harsh or abrasive cleansers.
•	Always clean in the direction of original polish lines.
			•	Allow dirt to accumulate.
• Always rinse well with clear water (2 or 3 times)		after
			•	Let plaster dust or any other construction residues reach the
	cleaning. Wipe dry completely.
•	You may also use a specialized household stainless steel			power pack During construction/renovation, cover the power

cleaner. pack to make sure no dust sticks to stainless steel surface.

Avoid when choosing a detergent:

-Any cleaners that contain bleach will attack stainless steel.

-Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.

-Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should never be used close to a range.

22. OPERATION

Always turn your power pack on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter.

HC0023
A	B	C	D

A.DELAY SWITCH:

When a blower speed is selected, press this switch to activate the delay function. The corresponding blower speed switch will flash to indicate this function is activated. The blower will continue to operate for 5 minutes and will stop automatically. To cancel the delay function, press the delay switch once again.

B.START/STOP/SPEED SELECTION SWITCHES:

Press the switch corresponding to the desired blower speed (from 1 for low speed to 4 for high speed). The chosen switch will light. To turn off the blower, press once more on the corresponding blower speed switch; the switch light will shut off. NOTE: When blower is off, pressing on blower speed 1 switch will cause the blower to start on high speed for a very

short lapse of time, and then resume on speed 1.

C.MASTER OFF/FILTER MAINTENANCE/HEAT SENTRY (TRIPLE FUNCTION SWITCH):

i.To turn off the blower(s) and the light simultaneously, press this switch once.

ii.After 25 hours of operation, this switch will light to indicate the filters and the blower wheel(s) need to be cleaned in order to maintain efficient operation of the unit. The switch light will stay on until the function is reset by pressing this switch for 3 seconds.

iii.The light indicator is used for the Heat Sentry function as well.

HEAT SENTRY: The hood is equipped with a protective device that activates when excessive heat is detected inside the hood and when it is set on speed 4. This device takes control of the blower and deactivates speed 4 for a 10-minute period and sets it on speed 3. During the Heat Sentry activation, only speed 3 can be used; the Heat Sentry button (C) will flash while the speed 3 button will light. The hood can also be turned OFF.

D.LIGHT SWITCH:

This switch allows three different lighting levels according to your needs. Press once for nightlight, twice for normal or three times to obtain full intensity. To shut off the lights without turning off the blower, press once more.

- 12 -