4.CONTROLS
4.1INTEGRATED CONTROL
All units are equipped with an integrated control, located under the unit, in front of the electrical compartment. Use the push button (1) to control the unit. The LED (2) will then show which mode the unit is in.
Refer to table below to see how to operate the unit using its integrated control.
WARNING | AVERTISSEMENT |
Risk of electric shock. Before performing | Danger d’électrocution. Débranchez |
any maintenance or servicing, always | toujours l’appareil avant d’entreprendre |
disconnect the unit from its power source. | des travaux d’entretien ou de réparation. |
|
|
|
|
|
|
|
| CAUTION |
|
| ATTENTION | |||||||||||||
|
| Unscrew both screws to open the electrical | Dévisser les deux vis pour ouvrir le compartiment | |||||||||||||||||||
| compartment. To completely remove, detach | électrique. Pour retirer complètement, le | ||||||||||||||||||||
|
|
| from its retention wire inside. | détacher de son fil de rétention intérieur. | ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
No light | OFF or remote controled |
|
|
|
|
|
|
|
|
|
| |||||||||||
Amber light | LOW speed |
|
|
|
|
|
|
|
|
|
| |||||||||||
Green ligh | HIGH speed |
|
|
|
|
|
|
|
|
|
| |||||||||||
Blinking light | See User Manual |
|
|
|
|
|
|
|
|
|
| |||||||||||
Sans lumière | Arrêté ou contrôlé |
|
|
|
|
|
|
|
|
|
| |||||||||||
| par contrôle mural |
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
Lumière ambre | Basse vitesse |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
Lumière verte | Haute vitesse |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
Clignotant | Voir guide d’utilisation |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VD0182 | 1 | 2 |
PRESS ON PUSH BUTTON | LED COLOR | RESULTS |
ONCE | AMBER | UNIT IS ON LOW SPEED |
TWICE | GREEN | UNIT IS ON HIGH SPEED |
THREE TIMES | NO LIGHT | UNIT IS OFF |
If a problem occurs during the unit operation, its integrated control LED (2) will blink. The color of the blinking light depends on the type of error detected. Refer to Section 11 Troubleshooting on last page for further details.
4.1.1BOOT SEQUENCE
The unit boot sequence is similar to a personnal computer boot sequence. Each time the unit is plugged in after being unplugged, or after a power failure, the unit will perform a
NOTE: No command will be taken until the unit is fully booted.
4.2ELECTRICAL CONNECTION TO OPTIONAL WALL CONTROLS
For more convenience, this unit can also be controlled using an optional main wall control.
NOTES: 1. The integrated control must be turned OFF to use an optional main control.
2. If an optional auxiliary control is used, if activated, this auxiliary control will override the optional main control.
!WARNING
Always disconnect the unit before making any connections. Failure in disconnecting power could result in electrical shock or damage of the wall control or electronic module inside the unit.
CAUTION
Never install more than one optional main wall control per unit. Make sure that the wires do not
Use the terminal connector included in the installation kit to perform the electrical connection for main and optional wall controls. Check if all wires are correctly inserted in their corresponding holes in the terminal block. (A wire is correctly inserted when its orange receptacle is lower than another one without wire. On picture beside, wire A is correctly inserted, but not wire B.)
AB
VE0106
- 17 -
