II. Preparation before threading, Thread tree | Brother 2340CV

II. Preparation before threading

Thread tree

	4	Raise the telescoping thread tree to its highest position.
	1	Make sure that the thread holders are in alignment above
	1	the spool pins as illustrated left.
		the spool pins as illustrated left.
		1Thread holder on thread tree
		2Spool pin
		3Spool cushion
	2	4Correct position
	2
	3

Thread spool

The procedure for placing the spool of thread on the spool pin differs according to the shape of the spool.

Type A

1

2

3

If you are sewing with loosely spun nylon thread, we recom- mend that you cover the spool with the net supplied to prevent the thread from slipping off the spool.

Adapt the net to the shape of the spool.

1Spool support

2Spool cushion

3Net

Type B

3

		1Spool support
	1	2Spool mat
	1	3Spool cap
		3Spool cap

2

Needle position

(1)

(2)

(1)Turn off the main power switch for safety.

(2)Set the needle bar in its highest position by turning the handwheel toward you.

Turn the handwheel to find the easiest position for threading.

8

Image 10

Brother 2340CV operation manual II. Preparation before threading, Thread tree, Thread spool, Needle position

Contents

English Español Important Safety Instructions English Page Names of parts and their functions Accessories includedCleaning brush X75906001 Hexagonal wrench Needle set Schmetz 130/705H Turning direction of motor Powering the machineHow to attach and remove the presser foot Opening and closing the front cover Stitch length Instructions for the differential feed mechanism Presser foot pressure 10mm 3/8 inch To remove the needle How to check the needleNeedle To insert the needle Thread tree Spool pins as illustrated leftII. Preparation before threading Thread spool Threading the left needle III. ThreadingNeedle threading Threading the center needle Looper threading Threading IV. Types of stitchesTri-cover stitch Three needles four threads cover stitch Left needle dial Center needle dial Two needles three threads cover stitch Needles and threading Mm 15/64 inch Wide Tension adjustmentsBalanced tension Needle and threading Removing the fabric from the machine SewingSewing flat fabric for example, trial sewing 2Raise the presser foot Do not take the seam Beginning and end of the stitching Sewing a cover stitchSewing tubular garments for example, cuffs Will prevent the seam from tearing Plain stitching Hem stitching StitchesCircular hemming VII. Machine specifications VI. MaintenanceChange the light bulb Notas Sobre EL Motor Nombres de las partes y sus funciones Accesorios incluidos Abre y cierre de la tapa delantera Encendido de la máquinaPara cambiar la dirección del motor Cómo colocar y retirar el prensatelas Largo de puntada Presión del prensatelas Para introducir la aguja AgujaPara sacar la aguja Descripción de la aguja Carrete de hilo II. Preparación antes del enhebradoArbol del hilo Posición de la aguja Enhebrado de la aguja izquierda III. EnhebradoEnhebrado de la aguja Enhebrado de la aguja central Enhebrado del áncora IV. Tipos de puntadas Puntada de recubierto de dos agujas con tres hilos Agujas y enhebrado Disco de la aguja Disco de la aguja central Mm AnchaTensión ajustada 1Aguja central Retirada del tejido de la máquina CosturaCostura de tejido plano por ejemplo, costura de prueba 2Suba el prensatelas No retire la costura 4Tire del tejido lentamente en la dirección de la flecha con Costura de puntada de recubierto Costura de prendas tubulares por ejemplo, puños Puntada básica Puntada de dobladillo Dobladillo de camisetas Puntadas Puntada simpleDobladillo circular VII. Especificaciones de la máquina VI. MantenimientoCambio de la bombilla de luz English / Español 884-500 XB1148-001 0308