Bryant Guide Specifications, General, Products, Air-Cooled, Split-SystemAir Conditioner 593C

GUIDE SPECIFICATIONS

GENERAL

System Description

Outdoor-mounted, air-cooled, split-system air conditioner unit suitable for ground or rooftop installation. Unit consists of a her- metic compressor, an air-cooled coil, propeller-type condenser fan, and a control box. Unit will discharge supply air upward as shown on contract drawings. Unit will be used in a refrigeration circuit to match up to a packaged fan coil or coil unit.

Quality Assurance

Unit will be rated in accordance with the latest edition of ARI Standard 240.

Unit will be certified for capacity and efficiency, and listed in the latest ARI directory.

Unit construction will comply with latest edition of ANSI/ ASHRAE and with NEC.

Unit will be constructed in accordance with UL standards and will carry the UL label of approval. Unit will have c-UL approval.

Unit cabinet will be capable of withstanding Federal Test Method Standard No. 141 (Method 6061) 500-hr salt spray test.

Air-Cooled condenser coils will be leak tested at 150 psig and pressure tested at 300 psig.

Delivery, Storage, and Handling

Unit will be shipped as single package only and is stored and handled per unit manufacturer’s recommendations.

Warranty (for inclusion by specifying engineer)

U.S. and Canada only.

PRODUCTS

Equipment

Factory assembled, single piece, air-cooled air conditioner unit. Contained within the unit enclosure will be all factory wiring, pip- ing, controls, compressor, refrigerant charge (R-22), and special features required prior to field start-up.

Unit Cabinet

Unit cabinet will be constructed of galvanized steel, bonderized, and coated with a powder coat paint.

Fans

Condenser fan will be direct-drive propeller type, discharging air upward.

Air-Cooled, Split-System Air Conditioner 593C

1-1/2 to 5 Tons Nominal

Condenser fan motors will be totally enclosed, 1-phase type with class B insulation and permanently lubricated bearings.

Shafts will be corrosion resistant.

Fan blades will be statically and dynamically balanced.

Condenser fan openings will be equipped with steel wire safety guards.

Compressor

Compressor will be hermetically sealed.

Compressor will be mounted on rubber vibration isolators.

Condenser Coil

Condenser coil will be air cooled.

Coil will be constructed of aluminum fins mechanically bonded to copper tubes which are then cleaned, dehydrated, and sealed.

Refrigeration Components

Refrigeration circuit components will include liquid-line shutoff valve with sweat connections, suction tube shutoff valves with sweat connections, system charge of R-22 (R-410A) refrigerant, and compressor oil.

Operating Characteristics
The capacity of the unit will meet or exceed			Btuh at a
suction temperature of		°F. The power consumption at full
load will not exceed	kw.

Combination of the unit and the evaporator or fan coil unit will

have a total net cooling capacity of					Btuh or greater at con-
ditions of			CFM entering air temperature at the evaporator
at	°F wet bulb and			°F dry bulb, and air entering the
unit at		°F.
The system will have an SEER of					Btuh/watt or greater at
DOE conditions.
Electrical Requirements
Nominal unit electrical characteristics will be						v, 1 single

phase, 60 hz. The unit will be capable of satisfactory operation

within voltage limits of v to v.

Unit electrical power will be single point connection.

Control circuit will be 24v.

Special Features

Refer to section of this literature identifying accessories and de- scriptions for specific features and available enhancements.

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

UNIT MUST BE INSTALLED IN ACCORDANCE

WITH INSTALLATION INSTRUCTIONS

Cancels: PDS 593C.18.6

© 2003 Bryant Heating & Cooling Systems, 7310 W. Morris St., Indpls., IN 46231 —28— PRINTED IN U.S.A. Catalog No. 5259-301 2-03