![](/images/new-backgrounds/1107402/10740275x1.webp)
|
|
| |||
| PTO PUMP & RESERVOIR KIT INSTALLATION |
| |||
| General Description CBH70 | 7. Reinstall Filter Element to the Filter Base. | |||
| 4.5 GPM Pump |
|
| 8. Assemble Pump P late ( 26) to Pump | (11) using |
| The PTO Pump Kit consists of those par ts required | two 3/8” NF x | |||
| to power the backhoe from the tractor’s PTO shaft. It | Nuts (4 ). P ump Plate may have to be readjusted | |||
| includes the PTO pump and adapter, reservoir, filtra- | later when inst alled on t ractor PTO Shaft. The P late | |||
| tion s ystem, hyd raulic hoses, and fittings. In addi - | may need to be turned 180 degrees to provide prop- | |||
| tion, it includes a pump pla te which attaches to the | er e ngagement with tractor drawbar and h ave ade - | |||
| tractor’s dra wbar and keeps the pump from t urning | quate clearances. |
| ||
| with the PTO shaft. |
|
| 9. Slide PTO Adapter (19) onto pump shaft, allowing | |
| NOTE: The speed of the backhoe operation increas- | 1/8” clearance between Adapter (19) in pl ace using | |||
| es as PTO speed increases. |
| two Setscrews (9) and 5/16” NC Nuts (2). |
| |
| Assembly |
|
| 10. Assemble Suction Hose (12) to Pump (11) using | |
|
|
| Reducer F itting (1 5) an d 90 D egree Barbed Fitti ng | ||
| IMPORTANT - When installing hoses and fitt ings | (16) Secure Hose using Hose Clamp. |
| ||
| always use thread sea lant in permanent connec - | 11. Connect 36” H ydraulic Hose (21) to Inlet Li ne | |||
| tions. Do not use thread sealant in union ends of | steel oil line located under Left Hand Foot Pad area | |||
| adapters. Do not | over tighten fittings - t hey can | of the backh oe mainframe. Co mplete connection to | ||
| split or expand, causing leakage. | Pump using 90 Adapter Union (14). |
| ||
| IMPORTAN T - Ha ve a sui table ho ist avail able | IMPORTANT - If hoses are connected incorrectly, | |||
| before proceeding with loader setup. | serious damage to the backhoe valve will result. | |||
| 1. Assemble Filler Tube (27) and B reather Cap with | 12. NOTE: Initial fill up of Reservoir Tank will require | |||
| Dipstick (28) to Reservoir Tank (20). | ||||
| 2. Assemble Reser voir Tank (20) to backhoe main - | ed fluid to corr ect level; refer to Service | Section in | ||
| frame using 5/16” NF Locknuts (3). | the Backhoe Manual. |
| ||
| 3. Preassembly of Filter Base and Element (22): | 13. Install the backhoe to the t ractor at this time fol - | |||
| lowing the ins tallati on pro cedure in the | Attaching | |||
| Remove Filter El ement from b ase t o e ase installa - | Section of the manual. |
| ||
| tion. Assemble Pipe Nipple ( 5) to “Inlet” por t on filter | 14. Sli de co mplete Pump a ssembly on to the PTO | |||
| base (22). |
|
| shaft o f th e tracto r, ma king su re locki ng c ollar on | |
| Assemble 90 Degree Adapter Union ( 13) to “Outlet” | PTO Adapter has locked into position. |
| ||
| port on filter base (22). |
| IMPORTANT - Make sure kinks DO N OT develop | ||
| 4. Assemble Filter Base (22) to R eservoir Tank (20) | in a ny of the li nes. Suct ion hose can be short - | |||
| using 90 Degree Pipe Elbow (7) and 45 Degree Pipe | ened to prevent this problem. |
| ||
| Elbow (6). |
|
| ! CAUTION |
|
| NOTE - Change Filter Element (29) every time oil is |
| |||
| changed. |
|
| DO NOT REMOVE THE TRACTOR PTO SHIELD! | |
| 5. A ssemble Suction Hose (12) to s traight B arbed | 15. Pump Plate (26) may be adjusted (turned front to | |||
| back or bottom to top) on Pump (11) for proper | ||||
| Fitting (17) using Hose Clamp (18). C onnect assem- | to tractor drawbar or three p oint mount if necessary. | |||
| bly to 90 Degree Adapter Union (13) installed earlier | The o ptimum p osition is to have t he plate pointin g | |||
| on the Filter Base and Element (22). | down and o ver the drawbar with the offset towards | |||
| 6. Install 9 0 De gree Adapter | Uni on ( 25) top upp er | the tractor. Refer to illustration. |
| |
| port o n Reservoir | Tank (2 | 0). Inst all 9 0 Degree | An alternate position for the Pump Plate may have it | |
| Adapter Union (24) to Retu rn Line “Check Valve” in | ||||
| upper steel oil line located under Left Hand Foot Pad | pointed upwards an d reta ined b y t he U pper Bar of | |||
| area of the ba ckhoe mainframe. Complete return | the Th ree Point Mount Kit. Whatever | position is | ||
| line connection to Rese rvoir T ank usi ng Steel Oil | selected, it is importa nt that the pump be rest rained | |||
| Line (23). |
|
| from rotating. Refer to illustration. |
|
36