2. With the help of a second person, carefully raise the
Right and Left Handrails (6, 7) to the position shown.
3. With the help of a second person, carefully tip the tread-
mill onto its left side. Hold the Base (71) against the Right
Handrail (6) and the Left Handrail (not shown). Make
sure that the Wheels (15) are toward the front of the
treadmill as shown.
Using a 9/16” socket spanner, attach the Base (71) to the
Right Handrail (6) with two Handrail Bolts (12), two
Handrail Washers (31), and two Handrail Nuts (17). Do
not tighten the Handrail Nuts yet. Attach the Base to
the Left Handrail (not shown) in the same way. Tighten
all four Handrail Nuts.
Tip the treadmill back to the position shown in step 1.
MAINTENANCE AND TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 7.) If an ex-
tension cord is needed, use only a 3-conductor, 1mm2 (14-gauge) cord that is no longer than 1.5
m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. UNPLUG THE POWER CORD. Check the batteries in the console (see assembly step 7 on page
6). Most problems are the result of drained batteries.
b. Remove the key from the console and UNPLUG THE POWER CORD. Remove the screws from
the hood, and carefully remove the hood.
Locate the Reed Switch (46) and the Magnet (49) on
the left side of the Pulley (53). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 3 mm (1/8 in.). If necessary, loosen
the Screw (26) and move the Reed Switch slightly.
Retighten the Screw. Re-attach the hood, and run the
treadmill for a few minutes to check for a correct
speed reading.
Tripped
Reset
Tripped Reset
c
49
26
46
Top View
53
17
6
31 71
12
15
3
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant
on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included allen wrench and your own phillips screwdriver ,
adjustable spanners , and 9/16” socket spanner .
6
7
2
14
14
71 42
42
115
15
1. Using two adjustable spanners, attach the Wheels (15) to
the Base (71) with the two Wheel Bolts (14) and the two
Wheel Nuts (42) as shown. Do not overtighten the
Wheel Bolts; the Wheels should turn freely.
12 5
b3 mm
WARNING: Do not plug in the power
cord until the treadmill is completely assembled.