Changing the burner orifices | Cal Flame LTR50001038 specification

30Gas Conversion (continued)

Appendix	Step 2: Changing the burner orifices
	Step 2: Changing the burner orifices
	1. Replace the main burner orifices
	a. Remove the grates, flame tamers, and drip tray
		from the grill. See figure below.

b.Remove the locking pins from the end of the burners.

The locking pins are accessible by removing the drip tray and tilting the grill back. They can be seen underneath the grill in the back. See figures below.

c.Remove all burners by carefully lifting them up and away from the valve orifice.

Burner

Locking Pin

You will need:

•6mm socket or nut driver

•Two to five 1.9mm orifices (depending on your grill

•Pipe compound suitable for natural gas

Orifice

d.Using a 6mm socket or nut driver, remove the orifice for the burner.

e.Apply a small amount of pipe compound to the orifice threads.

f.Screw in the orifice until it is finger tight.

g.Tighten the orifice with the 6mm wrench.

h.Repeat the above steps for the remaining burners.

i.Replace the burners, flame tamers, drip tray, and grates.

You do not need to replace the locking pins. They are used to keep the burners in place during shipping and are not necessary to operate your grill.

Barbecue Grills

www.calflamebbq.com

LTR50001038, Rev. C

Image 32

Cal Flame LTR50001038 manual Changing the burner orifices, Replace the main burner orifices

Contents

LTR50001038, Rev. C 12/26/11 Read all instructions before you Operate your grill Safety Instructions Placement and LocationInstructions Set-Up Storage Maintenance and RepairPrecautions Regarding Children Built-in Construction Location of grill enclosureConstruction materials This section Built-in Dimensions Model Description Width Depth Height Built-in Construction Model Description Width Depth Enclosure Ventilation Plumbing for Side Burners Electrical Supply Requirements Installation Installing the Transformer Installing Grills in Barbecue Islands Installing the Rotisserie Gas Requirements and Connection Leak Testing ProcedureGas Connection Cylinder Specification LP GasTank Requirements LP Gas Hook Up Connection Natural GasRequirements Basic Grill Operation Using Your GrillYour Grill Using GrillYour Grill Controls UsingYour Grill Lighting the BurnersElectronically Lighting the Burners Manually Lighting the Burners Heat Distribution on the Cooking Grates Convection Fan Cooking with the Rotisserie Loading food on the rotisserie rod Optional Grill Accessories OptionalSear Zone Infrared Burner Pizza Brick Tray Placement Using the Charcoal TrayRemoval and Clean-up Charcoal Tray Pull-Out Cutting Board Deep Fryer Helper SetGriddle Tray Cleaning and Maintenance MaintenanceStainless Steel Care and Cleaning Cleaning Products and Materials Cleaning the Interior of Your Grill Rust RemovalBurners Rust removal with Instant Rust Out Steam Cleaning Your Grill Covering Your GrillCooking Grates Drip Pan Remove the burners Seasonal CleaningClean the burners Clean the grill interior Clean the componentsReplace the burners Replace the components Snap-in Light Lens Light Bulb ReplacementLight Lens with Screw Clip Troubleshooting Appendix Problem Yellow Flame Problem Plugged orificeProblem Misalignment of Igniter on Burner Problem Flashback Switching the regulator Converting from LP to NGBehind the grill With your grill Changing the burner orifices Replace the main burner orifices Appendix Mark the rating plate Installing Sear Zone Burners Wiring Diagram Replacement Parts Ordering replacement parts Part Grill Size Limited Warranty Extent of WarrantyWarranty Performance Warranty Limitations Legal Remedies Customer ServiceDisclaimers Don’t forget to register your new product at Locating the product serial number