Light, Option, Controls Pump 2 and Pump 3 Sequence

Operating Your Spa

Light

Press the Light button to turn on the light. Press it once again to turn the light off. All optional lighting such as the control panel light and cabinet perimeter lighting is controlled by the Light button and will turn on and off with the spa light.

Option

Press the Option button to turn on the pump 2. Press it once again to turn off the pump 2 (6200 Controls only).

6300 Controls - Pump 2 and Pump 3 Sequence

•Press Option button once to activate high speed pump 2.

•Press Option button twice to activate high speed pump 3 and high speed pump 2

•Press 3 times to activate pump 3 hi speed only

•Press 4 times to turn pumps off

Automatic Time outs

These features will automatically turn themselves off during periods of continuous use:

•	Low speed pump	After 4 hours
•	High speed pumps	After 15 minutes
•	Optional circulation pump	After 15 minutes
•	Optional turbo	After 15 minutes
•	Spa light	After 15 minutes

Setting Filtration Cycles

Your spa is programmed to filter twice a day. The first cycle will begin 6 minutes after the spa is turned on and the second cycle 12 hours later. The factory has programmed the cycle to last for 2 hours but this can be switched to 4, 6, or 8 hours depending on your requirements. To set filtration time, turn off the power to the spa at the time of day you would like one of the filtration cycles to begin then turn back on after 30 seconds. When power has been restored, press the Temp button then the Jets button. Press Temp button again to change the filtering cycle duration. When desired duration is selected press the Jets button to exit.

At the beginning of each filtering cycle the Turbo system will run for approximately 30 seconds. The low speed pump will run for the duration of the filtering cycle and if an Ozone system is installed it will be activated. During filtering, FC will appear on the main display.

Diagnostic Messages

Message	Meaning
--	Spa temperature is unknown. After pump has been running for 2 minutes temperature will be
	displayed.
HH	Overheat protection (spa is shutdown) DO NOT ENTER THE WATER! One sensor has detected
	118˚F (48˚C) at the heater. Remove the spa cover and allow spa to cool below 107˚F (42˚C).
	Press any button on the topside display to reset spa. If spa will not reset after spa has cooled,
	turn off power for approximately 30 seconds and then turn power back on. If display message is
	repeated then shut the power off to the spa and call your dealer or service organization.
OH	Overheat protection (spa is shutdown) DO NOT ENTER THE WATER! If the spa has reached
	110˚F (43˚C), remove the spa cover to cool the water. At 107˚F (42˚C), the spa should reset
	itself. If the spa does not reset, then shut the power off to the spa, wait 30 seconds and restore
	power to spa. If display message is repeated then shut the power off to the spa and call your
	dealer or service organization.
IC	A possible ice condition exists within the spa. No action is required, the pump will automatically
	activate.
SA or Sb	Spa is shut down. Spa has detected that one of the sensors is not operating properly. One
	of these may display briefly during overheat then disappear when overheat situation has been
	resolved. Call your dealer or service organization if message does not go away.
Sn	Sensor (Spa is shut down). The high limit or water temperature sensors are not working correctly.
	Call your dealer or service organization.

Page 12	2008 Portable Spa Owner’s Manual

LTR20081000, Rev. D

GFCI specifications

Cal Spas GFCI (Ground Fault Circuit Interrupter) is an essential safety feature incorporated in Cal Spas hot tubs and spas, designed to protect users from electrical shocks and enhance overall safety during relaxation. This advanced technology monitors the electrical current flowing through the spa's components, providing peace of mind for families and individuals enjoying their hydrotherapy experience.

One of the main features of the Cal Spas GFCI is its quick response time. The GFCI continuously measures the current balance between the hot and neutral wires. If it detects an imbalance, potentially caused by faulty wiring or a short circuit, it immediately trips the circuit, cutting off power to the unit within a fraction of a second. This rapid response significantly minimizes the risk of electrical accidents, making it a vital component for any outdoor or indoor spa setup.

Another key characteristic of the Cal Spas GFCI is its user-friendly design. The GFCI outlet is often equipped with a reset button, which allows users to quickly restore power once the issue has been addressed. This feature eliminates the need for complicated maintenance procedures, ensuring that users can enjoy their spa without frequent interruptions.

Incorporating state-of-the-art technology, Cal Spas GFCI is designed to withstand the rigors of outdoor environments. The durable exterior of the GFCI unit protects it from exposure to moisture, debris, and other potential hazards, leading to increased longevity and reliability. Moreover, the GFCI meets the highest safety standards and regulations, providing confidence to consumers that they are investing in a safe product.

Another highlight of the Cal Spas GFCI is its compatibility with a variety of hot tub configurations. This flexibility allows it to work seamlessly with different Cal Spas models, delivering consistent safety features across the entire range. Additionally, installation is straightforward, with many users opting for professional installation to ensure it is set up correctly.

In summary, Cal Spas GFCI enhances the safety of hot tub and spa experiences through its quick trip response, durable design, user-friendly functionalities, and compatibility with various models. By integrating this technology, Cal Spas demonstrates its commitment to providing a safe and enjoyable environment for relaxation and rejuvenation.

Cal Spas GFCI manual Light, Option, Controls Pump 2 and Pump 3 Sequence, Automatic Time outs

Models: GFCI