Front panel controls
Volume
azur 540R
AV Receiver
|
|
|
|
|
|
|
|
|
|
|
| 19 |
|
|
|
| 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 |
|
1 | 2 | 3 | 4 | DVD | Video 1 | Video 2 | Video 3 | Tuner FM/AM Tape/MD/CDR CD/Aux | 6.1 Direct |
| ||
|
|
|
|
|
|
| 18 |
| ||||
Standby / On | Phones | – Tuning + | Mode/Store |
|
|
|
|
|
|
| Video Left Right | |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| 20 |
|
|
|
|
| Stereo | Dolby Digital EX/ Pro Logic II/ | DSP | Input |
|
| ||
|
|
|
|
| Modes | DTS ES |
| Neo 6 |
| Mode |
| Video 3 inputs |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| 5 | 6 |
| 7 | 8 | 9 |
|
|
1Standby/On
Switches the unit between Standby mode (indicated by dim power LED) and On (indicated by bright power LED). Standby is a low power mode where the power consumption is less than 10 Watts. The unit should be left in Standby mode when not in use.
2Phones
Allows for the connection of stereo headphones with a 6.35mm/¼" Jack plug. Headphones with an impedance of between 32 and 600 ohms are recommended.
Note: Plugging in headphones will automatically mute the main and pre- amp outputs and select a
3Tuning +/-
Used to tune FM/AM frequencies and skip presets in Tuner mode.
4Mode/Store
Press to cycle between Tuner modes (refer to the ‘Operating instructions’ section of this manual for more information).
Note: The 540R v3 remembers the audio and video input type and processing mode for each individual source input. These are recalled each time a source is selected.
5Stereo Modes
Press to listen to a source in either Stereo or Stereo + Sub modes.
6Dolby Digital EX / DTS ES
Press to select Dolby Digital or DTS surround modes (with suitably encoded digital source material). These modes can only be decoded from digital audio sources (via Coaxial or Optical inputs).
7Pro Logic II / Neo:6
10DVD
Press to select the DVD source equipment for output through the 540R v3.
11Video 1
Press to select the source equipment connected to Video 1 for output through the 540R v3.
12Video 2
Press to select the source equipment connected to Video 2 for output through the 540R v3.
13Video 3
Press to select a video camera recorder/video games console connected to the Video 3 input sockets.
14Tuner FM/AM
Press to select the tuner for output through the 540R v3. Once in Tuner mode also use this button to switch between FM and AM modes.
15Tape/MD/CDR
Press to select the recording device connected to the Tape/MD/CDR input for output through the 540R v3.
16CD/Aux
Press to select the CD or other source equipment connected to CD/Aux on the rear panel for output through the 540R v3.
176.1 Direct
Press to select a 6.1 or 5.1 source
18Infrared sensor
Press to select between various Pro Logic II/Neo:6 effects for matrix encoded analog or digital material or for
Note: The 540R v3 is unable to
8DSP
The 540R v3 can create a surround sound effect even from non- encoded material by Digital Signal Processing (DSP). Press this button to choose one of the following surround sound effects: THEATER, HALL, MOVIE, MUSIC or ROOM.
9Input Mode
Receives IR commands from the supplied Azur remote control. A clear unobstructed line of sight between the remote control and the sensor is required.
19Volume
Use to increase/decrease the level of the sound from the outputs of the 540R v3.
20Video 3 input sockets
Allows a video camera recorder/video games console to be connected and selected by the Video 3 source button.
Press this button to toggle between analog or optical/coaxial digital input types for the currently selected source. The 540R v3 remembers the input type selected for each source when you return to that source.
6