Campbell Hausfeld CHN10600 specifications User-Maintenance Instructions, Fasteners

CHN10600

Operating Instructions (Continued)

3.Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the power source if a regulator fails, or 150 psi, whichever is greater. Use 1/4 in. air hose for runs up to 50 ft. Use 3/8 in. air hoses for 50 ft. run or longer. For better performance, install a 3/8 in. quick plug (1/4 in. NPT threads) with an inside diameter of

.315 in. (8mm) on the tool and a 3/8 in. quick coupler on the air hose.

150 psi or greater

3/8 inch I.D.

4.Use a pressure regulator on the compressor, with an operating pressure of 0 psi - 125 psi. A pressure regulator is required to control the operating pressure of the tool between 60 psi and 100 psi.

OPERATIONAL MODE

Always know the operational mode of

the tool before using. Failure to know the operational mode could result in death or serious personal injury.

TRIGGER ONLY MODE (WITH TRIGGER LOCK)

The tool is a single-actuator device. This mode requires that, with the trigger lock not positioned in the safe mode, only a pull of the trigger will fire a fastener.

After verifying there are no fasteners in the tool, safety check the operation of the activated trigger lock to prevent the tool from firing a fastener before storage. Always disconnect from

compressed air when not in use.

LOADING/UNLOADING THE TOOL

1.Always connect the tool to the air supply before loading fasteners.

2.Turn stapler upside down and depress the latch. Pull back on the magazine cover.

3.Insert a stick of Campbell Hausfeld staples or equivalent (see Fastener Section)

into the magazine with the crown side down. Make sure the staples are not dirty or damaged.

4.Push the magazine cover forward until the latch catches.

5.Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except

always disconnect the air hose before unloading.

ADJUSTING THE DIRECTION OF THE EXHAUST

The tool is
equipped with
an adjustable	Rotate
direction exhaust

deflector. This is intended to allow the user to change the direction of the exhaust. Simply twist the deflector to any direction desired.

CLEARING A JAM FROM THE TOOL

1.Disconnect the air supply from the tool.

2.Remove all fasteners from the magazine (see "Loading/ Unloading The Tool").

3.With the magazine open, remove the jammed fastener, using pliers, a screwdriver or a pick if required.

4.Close magazine.

User-Maintenance

Instructions

TECHNICAL SERVICE

Please call our Tool Hotline at 1-800- 543-6400 with any questions regarding the operation or repair of this tool or for additional copies of this manual.

FASTENER AND REPLACEMENT PARTS

Use only 1/2 in. crown 21 gauge staples.

Tool performance, safety and durability could be reduced if improper fasteners are used. When ordering replacement parts or fasteners, specify by part number.

TOOL REPAIR

Only qualified personnel should repair the tool and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently.

ASSEMBLY PROCEDURE FOR SEALS

When repairing a tool, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W non-detergent oil or equivalent, must be added through the air line before testing.

STORAGE

The stapler should be stored in a cool dry place.

Fasteners

The following fasteners are available at local retail stores. If you need help locating any item, call customer service at 1-800-543-6400.

BrandType

Arrow#609

Duofast G series

www.chpower.com

5