Operating Instructions |
|
|
|
| CHN20103 | ||
Important Safety Instructions | Use |
| 3. | After adding oil, run |
| ||
(Continued) |
| only a |
|
| tool briefly. Wipe off |
| |
|
|
|
| ||||
Disconnect air |
|
|
| any excess oil from |
| ||
| compressed air source to limit | 110 psi |
|
| |||
supply and release |
| the cap exhaust. |
| ||||
the air pressure supplied to |
|
|
| ||||
tension from the pusher before |
|
|
|
|
| ||
| the tool. The regulated pressure must | Recommended Hookup |
| ||||
attempting to clear jams because |
|
| |||||
| not exceed 110 psi. If the regulator |
| |||||
|
|
|
| ||||
fasteners can be ejected from the front | The illustration below shows the |
| |||||
fails, the pressure delivered to the |
| ||||||
of the tool. Personal injury may occur. | tool must not exceed 200 psi. The tool | recommended hookup for the tool. | |||||
|
| ||||||
Air Source |
| could explode which will cause death or | 1. | The air compressor | 70 psi | ||
| serious personal injury. |
| |||||
a. Never connect to an air source that |
|
| must be able to | Min. | |||
|
|
| |||||
Save These Instructions |
| 110 psi | |||||
is capable of exceeding 200 psi. |
| maintain a minimum | |||||
Do Not Discard |
|
| Max. | ||||
Over pressurizing the tool is able |
|
| of 70 psi when the | ||||
|
|
|
| ||||
to result in bursting, abnormal |
| Operating Instructions |
|
| tool is being used. An inadequate air | ||
operation, breakage of the tool or |
|
|
| supply can cause a loss of power and | |||
serious injury to persons. Use only | Lubrication |
|
| inconsistent driving. |
| ||
clean, dry, regulated compressed air | This tool requires lubrication before | 2. An oiler can be |
| ||||
at the rated pressure or within the | using the tool for the first time and |
| used to provide oil |
| |||
rated pressure range as marked on | before each use. If an inline oiler is |
| circulation through |
| |||
the tool. Always verify prior to using | used, manual lubrication through the |
| the tool. A filter can |
| |||
the tool that the air source has been | air inlet is not required on a daily basis. |
| be used to remove liquid and solid | ||||
adjusted to the rated air pressure or | The work surface |
| impurities which can rust or “gum | ||||
within the rated |
| ||||||
can become |
|
| up” internal parts of the tool. |
| |||
b. Never use oxygen, carbon dioxide, | damaged by excessive lubrication. | 3. Always use air supply hoses with | |||||
Proper lubrication is the owner’s | |||||||
combustible gases or any bottled | |||||||
| a minimum working pressure |
| |||||
responsibility. Failure to lubricate the |
|
| |||||
gas as an air source for the tool. |
|
| |||||
tool properly will dramatically shorten |
| rating equal to or greater than the | |||||
Such gases are capable of explosion |
| ||||||
the life of the tool and void your |
| pressure from the power source if a | |||||
and serious injury to persons. |
| warranty. |
|
| |||
|
|
| regulator fails, or 150 psi, whichever | ||||
Do not |
|
|
|
| |||
| 1. Disconnect the air |
|
| is greater. Use 1/4 inch air hose for | |||
use any |
| supply from the tool |
|
| runs up to 50 feet. Use 3/8 inch or | ||
type of reactive gases, | O CO2 |
|
| ||||
to add lubricant. |
|
| |||||
including, but not limited |
|
|
| greater air hoses for 50 foot run or | |||
|
|
|
| longer. |
| ||
to, oxygen and combustible |
| 2. Turn the tool so the |
|
|
| ||
gases, as a power source. Use filtered, |
|
|
|
| |||
lubricated, regulated compressed air | air inlet is facing up. Place | OIL |
| 150 psi or greater |
| ||
only. Use of a reactive gas instead of |
|
|
|
| |||
compressed air may cause the tool | detergent oil into air inlet. |
| 4. | Use a pressure regulator on the | |||
to explode which will cause death or |
| ||||||
Do not use detergent oils, |
| ||||||
serious personal injury. |
|
|
| compressor, with an operating | |||
| oil additives, or air- tool |
|
| ||||
|
|
|
| pressure of 0 - 125 psi. A pressure | |||
|
|
|
|
| |||
oils. Air tool oils contain solvents | regulator is required to control | |
which will damage the tool's | ||
the operating pressure of the tool | ||
internal components. | ||
between 70 and 110 psi. | ||
|
Recommended Hookup
Quick Plug | Quick Plug (Optional) | Regulator |
|
|
Quick |
| Quick |
Coupler |
| Coupler |
| Air Hose | (Optional) |
| Filter | |
|
| |
|
| Lubricator |
www.chpower.com | 4 |