Operating Instructions

 

 

 

 

 

 

 

CHN20103

User - Maintenance

Technical Service

 

 

Assembly Procedure For Seals

Instructions

Please call our Tool Hotline at 1-800-

When repairing a tool, the internal

Clearing A Jam From The Tool

543-6400 with any questions regarding

parts must be cleaned and lubricated.

1.

Disconnect the air

the operation or repair of this tool or

Parker O-lube or equivalent must be

for additional copies of this manual.

used on all o-rings. Each o-ring must be

 

supply from the

 

 

 

 

 

coated with O-lube before assembling.

 

tool.

Fastener And Replacement

 

 

 

A small amount of oil must be used on

 

 

Parts

 

 

 

 

 

 

 

 

all moving surfaces and pivots. After

 

 

 

Use only headless

2.

Remove all nails

 

reassembling, a few drops of 30W

 

 

micropins, 16 gauge.

 

 

non-detergent oil or equivalent, must

 

from the magazine

Tool performance, safety and durability

 

be added through the air line before

 

(see Loading/

could be reduced if improper fasteners

 

are used. When ordering replacement

testing.

 

 

 

 

Unloading). Failure

 

 

 

 

parts or fasteners, specify by part

 

 

 

 

 

 

 

to do so will cause

 

Storage

 

 

 

 

number.

 

 

 

 

 

 

 

the nails to eject from the front of

 

 

 

 

 

 

 

Tool Repair

 

 

 

The tool should be stored in a cool dry

 

the tool.

 

 

 

 

 

 

 

place.

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Undo latch by

Only qualified personnel should repair

 

 

 

 

 

 

 

 

 

the tool and they should use genuine

 

 

 

 

 

 

pulling out

 

 

 

 

 

 

Campbell Hausfeld replacement parts

 

 

 

 

 

 

and down. The

 

 

 

 

 

 

and accessories, or parts and accessories

 

 

 

 

 

 

wire latch will

 

 

 

 

 

 

which perform equivalently.

 

 

 

 

 

 

 

disengage from

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the hooks on the nose.

 

 

 

 

 

 

 

 

 

4.

The door can

 

 

 

 

 

 

 

 

 

 

now be rotated,

 

 

 

 

 

 

 

 

 

 

exposing the

 

 

 

 

 

 

 

 

 

 

jammed fastener.

 

 

 

 

 

 

 

 

 

5.

Remove the

 

 

 

 

 

 

 

 

 

 

jammed fastener,

 

 

 

 

 

 

 

 

 

 

using pliers or

 

 

 

 

 

 

 

 

 

 

a screwdriver if

 

 

 

 

 

 

 

 

 

 

required.

Fasteners

 

 

 

 

 

 

 

 

6.

Rotate door back

 

 

 

 

 

 

 

 

The following Campbell Hausfeld finishing nails are available at local retail stores.

 

into the closed

 

If you need help locating any item, call customer service at 1-800-543-6400.

 

 

position.

 

 

Campbell Hausfeld nails meet or exceed ASTM Standard F1667.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Nails

Nails

7.

Extend the wire

 

 

Shank

 

 

 

 

Per

Per

Model

Length

Gauge

Finish

Head

Collation

Stick

Box

 

latch and place

 

 

 

 

 

 

 

 

 

 

 

over the hooks on

FB005060

2

16

Galvanized

Brad

Adhesive

50

2500

 

the nose.

 

inch

Gauge

 

 

 

 

 

 

8.

Close the latch by

FB160025

1

16

Galvanized

Brad

Adhesive

50

1000

 

pushing the latch

 

inch

Gauge

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

up and in until the

FB160040

1-1/2

16

Galvanized

Brad

Adhesive

50

1000

 

latch snaps into

 

inch

Gauge

 

 

 

 

 

 

 

place.

FB160065

2-1/2

16

Galvanized

Brad

Adhesive

50

1000

9.

Make sure the

 

inch

Gauge

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

trigger and work

Interchange Information

 

 

 

 

 

 

 

contact element

 

 

 

 

 

 

 

(WCE) move freely

Nails used in the Campbell Hausfeld CHN201 Finishing Nailer will also work in

 

up and down

Hitachi NT65A, Paslode 3250-F16, IM250F, Duo Fast LFN-764, Sears 18321, Porter

 

without sticking or binding.

Cable FN200 and FN250.

 

 

 

 

 

 

www.chpower.com

6