Operating Instructions

 

 

 

 

 

CHN10302, CHN10310

Important Safety Instructions

Operating Instructions

 

Recommended Hookup

 

(Continued)

 

Lubrication

 

 

The illustration below shows the

 

Air Source

 

 

 

recommended hookup for the tool.

 

This tool requires lubrication before

a. Never connect to an air source that

1.

The air compressor

 

using the tool for the first time and

60 psi

is capable of exceeding 200 psi.

 

must be able to

Min.

before each use. If an inline oiler is

 

Over pressurizing the tool is able

 

maintain a minimum

100 psi

used, manual lubrication through the

 

to result in bursting, abnormal

 

of 60 psi when the

Max.

air inlet is not required on a daily basis.

 

 

operation, breakage of the tool or

 

tool is being used. An inadequate air

 

The work surface

 

serious injury to persons. Use only

 

 

supply can cause a loss of power and

 

can become

 

 

clean, dry, regulated compressed air

 

 

 

inconsistent driving.

 

damaged by excessive lubrication.

 

 

at the rated pressure or within the

Proper lubrication is the owner’s

2. An oiler can be

 

rated pressure range as marked on

responsibility. Failure to lubricate the

 

 

used to provide oil

 

the tool. Always verify prior to using

tool properly will dramatically shorten

 

 

 

circulation through

 

the tool that the air source has been

the life of the tool and void your

 

 

 

the tool. A filter can

 

warranty.

 

 

 

 

adjusted to the rated air pressure or

 

 

 

 

1. Disconnect the air

 

 

be used to remove liquid and solid

within the rated air-pressure range.

 

 

 

 

impurities which can rust or “gum

supply from the tool

 

 

b. Never use oxygen, carbon dioxide,

 

 

 

 

up” internal parts of the tool.

 

to add lubricant.

 

 

 

combustible gases or any bottled

 

 

 

 

 

 

 

3. Always use air supply hoses with

gas as an air source for the tool.

 

 

 

2. Turn the tool so the

 

 

a minimum working pressure

 

Such gases are capable of explosion

OIL

 

 

air inlet is facing up. Place

 

 

rating equal to or greater than the

and serious injury to persons.

 

 

4-5 drops of 30 W non-

 

 

pressure from the power source if a

Do not

 

 

 

 

detergent oil into air inlet.

 

 

regulator fails, or 150 psi, whichever

use any

 

 

 

 

Do not use detergent

 

 

is greater. Use 1/4 inch air hose for

type of reactive gases,

O CO2

 

 

including, but not limited

 

oils, oil additives, or air- tool oils.

 

runs up to 50 feet. Use 3/8 inch or

to, oxygen and combustible

 

Air tool oils contain solvents which

 

greater air hoses for 50 foot run

gases, as a power source. Use filtered,

will damage the tool's internal

 

or longer. For better performance,

lubricated, regulated compressed air

components.

 

 

 

install a 3/8 inch quick plug (1/4 inch

only. Use of a reactive gas instead of

 

 

 

3. After adding oil, run

 

 

NPT threads) with an inside diameter

compressed air may cause the tool

 

 

 

 

of .315 inch (8mm) on the tool and

to explode which will cause death or

tool briefly. Wipe off

 

 

serious personal injury.

 

any excess oil from

 

 

a 3/8 inch quick coupler on the air

Use

 

 

 

hose.

 

 

the cap exhaust.

 

 

 

only a

 

 

 

 

 

 

 

 

 

 

 

 

pressure-regulated

 

 

 

 

 

150 psi or greater

 

compressed air source to limit

100 psi

 

 

 

 

 

 

 

 

 

 

 

the air pressure supplied to

 

 

 

 

 

 

 

the tool. The regulated pressure must

 

 

 

4.

Use a pressure regulator on the

not exceed 100 psi. If the regulator

 

 

 

 

compressor, with an operating

fails, the pressure delivered to the

 

 

 

 

 

 

 

 

pressure of 0 - 125 psi. A pressure

tool must not exceed 200 psi. The tool

 

 

 

 

 

 

 

 

regulator is required to control

could explode which will cause death or

 

 

 

 

serious personal injury.

 

 

 

 

 

the operating pressure of the tool

Save These Instructions

 

 

 

 

between 60 and 100 psi.

 

 

 

 

 

 

 

Do Not Discard

 

 

 

 

 

 

 

Recommended Hookup

 

 

 

 

 

 

 

Quick Plug

 

Quick Plug (Optional)

 

 

Regulator

 

 

 

 

 

 

 

 

 

Quick

 

Quick

 

 

 

 

 

Coupler

 

Coupler

 

 

 

 

 

 

Air Hose

(Optional)

 

 

 

 

 

 

 

 

 

Filter

 

 

 

 

 

Lubricator

 

 

 

 

 

 

 

 

 

www.chpower.com

4