Campbell Hausfeld CHN10310, IN700502AV 6

Operating Instructions			CHN10302, CHN10310
User - Maintenance		7. Extend the wire	Assembly Procedure For Seals
Instructions		latch and place	When repairing a tool, the internal
Clearing A Jam From The Tool		over the hooks on	parts must be cleaned and lubricated.
Clearing A Jam From The Tool		the nose.	parts must be cleaned and lubricated.
1.	Disconnect the air	the nose.	Parker O-lube or equivalent must be
			Parker O-lube or equivalent must be
			used on all o-rings. Each o-ring must be
	supply from the	8. Close the latch by	used on all o-rings. Each o-ring must be
	supply from the	8. Close the latch by	coated with O-lube before assembling.
	tool.	pushing the latch	coated with O-lube before assembling.
	tool.	pushing the latch	A small amount of oil must be used on
		up and in until the	A small amount of oil must be used on
		up and in until the	all moving surfaces and pivots. After
		latch snaps into	all moving surfaces and pivots. After
2.	Remove all nails	latch snaps into	reassembling, a few drops of 30W
		place.	reassembling, a few drops of 30W
			non-detergent oil or equivalent, must
	from the magazine
		9. Make sure the
			be added through the air line before
	(see Loading/
		trigger and work
			testing.
	Unloading).
		contact element

			Storage
	Failure to remove	(WCE) move freely	Storage
	Failure to remove	(WCE) move freely
	all fasteners will	up and down	The tool should be stored in a cool dry
cause the fasteners to eject from the		without sticking or binding.	place.
front of the tool.
3.	Undo latch by	Technical Service
3.	Undo latch by	Please call our Tool Hotline at 1-800-
	pulling out	Please call our Tool Hotline at 1-800-
	and down. The	543-6400 with any questions regarding
	wire latch will	the operation or repair of this tool or
	disengage from	for additional copies of this manual.
	the hooks on the nose.	Fastener And Replacement
		Fastener And Replacement
4.	The door can	Parts
	now be rotated,	Use only headless
	exposing the	micropins, 18 gauge.
	jammed fastener.	Tool performance, safety and durability
		could be reduced if improper fasteners
5.	Remove the	are used. When ordering replacement
5.	Remove the	parts or fasteners, specify by part
	jammed fastener,	number.
	using pliers or	Tool Repair
	a screwdriver if	Tool Repair
	a screwdriver if	Only qualified personnel should repair
	required.	Only qualified personnel should repair
	required.	the tool and they should use genuine
6.	Rotate door back	the tool and they should use genuine
6.	Rotate door back	Campbell Hausfeld replacement parts
	into the closed	Campbell Hausfeld replacement parts
	into the closed	and accessories, or parts and accessories
	position.	and accessories, or parts and accessories
	position.	which perform equivalently.
		which perform equivalently.

Fasteners

The following Campbell Hausfeld finishing nails are available at local retail stores. If you need help locating any item, call customer service at 1-800-543-6400. Campbell Hausfeld nails meet or exceed ASTM Standard F1667.

		Wire	Crown				Nails Per	Nails Per
Model	Length	Diameter	Size	Point	Finish	Collation	Stick	Box
FN180615AV	1/2 inch	18 Gauge	1/4 inch	Chisel	Galvanized / Vinyl Coated	Adhesive	100	1000
FN180620AV	3/4 inch	18 Gauge	1/4 inch	Chisel	Galvanized / Vinyl Coated	Adhesive	100	1000
FN180625AV	1 inch	18 Gauge	1/4 inch	Chisel	Galvanized / Vinyl Coated	Adhesive	100	1000
FN180630AV	1-1/4 inch	18 Gauge	1/4 inch	Chisel	Galvanized / Vinyl Coated	Adhesive	100	1000

Interchange Information

Staples used in the Finishing Stapler will also work in: Senco LN4450, SJS-LR, SKS L11-15, Hitachi N3804A, Duofast BN-1832S, KN-1848, Stan-Tech SDS 18-14, Atro Minor 90/30, 90/32, 90/40, and Porter Cable NS100.