Operating Instructions

Operating Instructions

 

thumbwheel in place after each

7. Extend the wire latch and place over

(Continued)

 

 

 

adjustment..

 

the hooks on the nose..

4. Release the pusher.. Allow pusher to

3.

Make sure that

 

 

rest against nails.. The nailer is now

 

the trigger and

 

8. Close the latch by pushing the latch

loaded..

 

 

 

work contact

 

 

 

 

Rotate

up and in until the latch snaps into

 

 

 

 

element (WCE)

 

 

 

 

place..

UNLOADING THE Nailer

 

 

 

 

 

move freely up and down without

1. Always unload all fasteners before

 

9. Make sure the trigger and work

 

binding or sticking after each

 

contact element (WCE) move freely

removing tool from service..

 

 

adjustment..

 

 

 

up and down without sticking or

Unloading is the

 

 

 

 

 

 

 

 

 

 

Nail

Adjusting The Direction Of The

binding..

reverse of loading,

Pusher

except always

 

Mechanism

Exhaust

 

 

 

Nail Bypass Button

 

 

 

The NB356502 is

 

User-Maintenance

disconnect the

 

 

 

air hose before

 

 

equipped with an

 

Instructions

unloading..

 

 

adjustable direction

 

Technical Service

 

 

 

exhaust deflector.. This

 

2. Pull nail pusher

 

 

 

Please call our Tool Hotline at 1-800-

 

 

is intended to allow

 

mechanism back and

 

 

 

 

543-6400 with any questions regarding

 

the user to change the

 

press “Nail Bypass

 

 

 

 

the operation or repair of this tool or

 

direction of the exhaust..

 

Button..”

 

 

 

 

 

 

for additional copies of this manual..

 

 

Simply twist the deflector

 

 

 

 

 

3. Hold tool upright so

 

 

 

 

to any direction desired..

 

Fastener And Replacement

nails will slide out of

 

 

 

 

 

 

Parts

magazine..

 

 

Clearing A Jam From The Tool

 

 

Use only 15 gauge

 

 

 

1.

Disconnect the air

 

 

 

 

 

35° fasteners.

4. Release the Pusher..

 

 

supply from the tool..

 

 

 

 

Use only genuine Campbell Hausfeld

 

 

 

 

 

 

replacement parts. Never substitute

 

 

 

 

 

 

parts. Do not use modified parts or

 

 

 

2. Remove all nails from the magazine

parts which will not give equivalent

Adjusting

 

 

performance to the original equipment.

 

 

 

(see "Loading/

 

Tool performance, safety and durability

the Nail

 

 

 

Unloading The

 

could be reduced. When ordering

Penetration

COUNTER-￿

 

 

Nailer").. Failure to

 

replacement parts or fasteners, specify

 

CLOCKWISE

 

 

by part number.

The NB356502 is

CLOCKWISE

 

do so will cause the

 

 

 

 

 

 

 

 

 

equipped with an

 

 

 

nails to eject from the

 

Tool Repair

adjustable depth

 

 

 

front of the nailer..

 

Only qualified personnel should repair

of drive feature.. This allows the user to

 

 

 

3.

Undo latch by pulling

 

the tool and they should use genuine

determine how deep a fastener will be

 

 

out and down..

 

Campbell Hausfeld replacement parts

driven into the work surface..

 

 

 

 

 

The wire latch will

 

and accessories, or parts and accessories

 

 

 

 

 

1. Adjust the

 

 

 

disengage from the

 

which perform equivalently..

operating

 

 

 

hooks on the nose..

 

Assembly Procedure For Seals

pressure to a

 

 

4. The door can now be

 

 

 

 

When repairing a tool, the internal

pressure which

 

 

 

 

 

 

rotated, exposing the

 

will consistently

 

 

 

 

parts must be cleaned and lubricated..

 

 

 

jammed fastener..

 

drive the

 

 

 

 

Parker O-lube or equivalent must be

 

 

 

 

 

fasteners.. Do not exceed the

5.

Remove the jammed

 

used on all o-rings.. Each o-ring must be

maximum operating pressure of the

 

coated with O-lube before assembling..

nailer of 110 psi..

 

 

 

fastener, using pliers

 

A small amount of oil must be used on

2. To increase depth of drive, first

 

or a screwdriver if

 

all moving surfaces and pivots.. After

 

required..

 

reassembling, a few drops of 30W

pull up on the upper WCE, then

 

 

6.

Rotate door back into

 

non-detergent oil or equivalent, must

rotate thumbwheel to the left

 

 

the closed position..

 

be added through the air line before

(counter-clockwise)..

 

 

 

 

 

 

 

testing..

To decrease depth

 

 

 

 

 

 

 

 

 

of drive, rotate

 

Movement

 

 

Movement

Storage

thumbwheel to the

 

 

 

 

 

 

 

 

The stapler should be stored in a cool

right (clockwise).. Then release upper

 

 

 

 

 

 

dry place..

WCE into detents which hold the

 

 

 

 

 

 

 

www.chpower.com

 

 

 

 

 

 

6