Operating Instructions and Assembly Instructions

Airless Paint Sprayers

Preparation (Continued)

DO NOT ATTACH THE SUCTION ASSEMBLY UNTIL INSTRUCTED TO DO SO IN STEP 3.

1.Remove inlet valve cap and with your smallest finger, push on inlet valve stem to ensure it moves freely.

2.Push outlet prime button three times to ensure outlet valve is moving freely.

3.Attach suction assembly and bypass tube securely and place both suction and bypass tubes in cleaning solvent.

4.Turn pressure to High (completely clockwise).

5.Turn prime/spray control to the Prime position.

6.Turn power switch to the ON position. In a few seconds, cleaning solvent will begin to move up through the tube. Allow the fluid to circulate for one minute to ensure all air has been exhausted from the pump.

7.Turn prime/spray control to Spray position. Watch for any fluid leaks (See Troubleshooting Chart if leaks occur).

NOTE: If unit is building pressure properly, the pump should produce a knocking sound, which indicates it has reached its hydraulic relief pressure.

8.When flushing the system with cleansing fluid (either prior to use with paint or during cleaning process) the spray tip can remain in the clean position.

9.Point spray gun into an empty waste bucket and pull trigger. To reduce splashing, direct the fluid stream along the inside of the bucket wall and well above the fluid level.

Starting Instructions

2

1

Use Finger to

Push Outlet

Check Inlet Valve

Prime Button

3

4

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Turn Pressure

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Attach

 

 

 

 

 

 

to HIGH

 

 

 

Turn Prime/ Spray

 

Suction

(completely clockwise)

 

 

 

 

Control

Assembly

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to PRIME

 

(knob is horizontal)

6

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Turn Prime/ Spray

 

 

 

 

 

 

 

 

 

 

 

 

Power Switch

 

 

 

 

 

Control

 

 

Location

 

 

 

 

 

to SPRAY

 

 

 

 

 

 

 

 

 

 

 

 

(knob is vertical)

8

9

Tip in

While Pulling Trigger,

Direct Fluid Stream Along

Cleaning

Inside of Bucket

Position

 

www.chpower.com