Canon 2160B002 4.5 Adjustment and Setup Items

Chapter 4

4-33

4.5 Adjustment and Setup Items

4.5.1 Adjustment Item List

0017-5609

The following adjustment procedures need to be performed when parts have been replaced or remove and then

reinstalled:

T-4-1

4.5.2 Procedure after Replacing the Feed Roller or Feed Roller Encoder

0013-9977

Feed roller eccentricity is factory-adjusted (correction of variation in the paper feed amount per rotation). It is

necessary to adjust feed roller eccentricity after replacing the feed roller or feed roller encoder.

In the service mode, perform automatic adjustment of feed roller eccentricity.

Service mode : SERVICE MODE > ADJUST > PRINT PATTERN > LF TUNING

Media type : Photo glossy paper

Media size : Media having awidth equal to or larger than that of A2-size paper

If adjustment cannot be done properly by selecting "SERVICE MODE > ADJUST > PRINT PATTERN > LF

TUNING" (auto adjustment), carry out manual adjustment.

Service mode : SERVICE MODE > ADJUST > PRINT PATTERN > LF TUNING2

Media type : Photo glossy paper

Media size : Media having awidth equal to or larger than that of A2-size paper

Check the printed pattern and enter values for adjustment.

4.5.3 Procedure after Replacing the Carriage Unit or Multi Sensor

0013-9980

a) Multi Sensor Recalibration

Since multi sensors have individual electrical specificity, the following are recalibrated at the factory, namely,

the optical axis of the sensor, the sensor gain for measuring the printhead height and color reproduction.

Accordingly, carry out the following adjustments in the service mode whenever replacing the carriage unit or

multi sensor.

The multi sensor reference plate must be replaced at the same time whenever the carriage or the multi

sensor is being replaced.

-Service mode : SERVICE MODE > ADJUST > GAP CALIB.

-Service mode : SERVICE MODE > ADJUST > PRINT PATTERN > OPTICAL AXIS

Media type : Photo glossy paper

Media size : Media having a width equal toor larger then that of A2-size paper

Adjustment item Adjustment timing

Multi sensor recalibration Multi sensor replacement/removal

Carriage unit replacement/removal

Adjusting feed roller eccentricity Feed roller

Feed roller encoder

Head management sensor recalibration Head management sensor replacement/

removal

Carriage unit replacement/removal

Contents

Main Page Symbols Used Symbol Description Page Page Page Page Page Page Page 1.5 Names and Functions of Components........................................................ 1-18 1.1 Product Overview 1.1.1 Product Overview 1-2 1.2 Features 1.2.1 Features 1.2.2 Printhead 1-3 1.2.3 Ink Tank 1.2.4 Cutter unit 1.2.5 Roll Holder 1-4 1.2.6 Stand [A] [B] 1-5 1.2.7 IEEE1394 (FireWire) Board 1.2.8 Consumables Page 1-7 1.3 Product Specifications 1.3.1 Product Specifications 1-8 1-9 1-10 1.4 Detailed Specifications 1.4.1 Print Speed and Direction 1-11 Plain Paper/ Recycled Paper 1-12 1-13 1-14 1-15 1-16 1-17 1.4.2 Interface specifications 1-18 1.5 Names and Functions of Components 1.5.1 Front 1-19 1.5.2 Rear 1-20 1.5.3 Carriage 1-21 1.6 Basic Operation 1.6.1 Operation Panel 1-22 1.6.2 Main Menu 1-23 1-24 1-25 1-26 1-27 1-28 1-29 1-30 1-31 1-32 Setting Item 1-33 Setting Item 1-34 1-35 press the[ ] button. Choose [OK] to restore the network settings to the default values. 1-36 1-37 1-38 1-39 1-40 1.7 Safety and Precautions 1.7.1 Safety Precautions 1.7.1.1 Moving Parts 1-41 1.7.1.2 Adhesion of Ink 1-42 1.7.1.3 Electric Parts 1-43 1-44 1.7.2 Other Precautions 1.7.2.1 Printhead 1-45 1.7.2.2 Ink Tank 1-46 1.7.2.3 Handling the Printer 1-47 1-48 1.7.3 Precautions When Servicing Printer 1.7.3.1 Notes on the Data Stored in the Printer 1.7.3.2 Confirming the Firmware Version 1.7.3.3 Precautions against Static Electricity Page Page Page Page 2-1 2.1 Basic Operation Outline F-2-1 2.1.1 Printer Diagram Shown below is a printer diagram. Chapter 2 2.1.2 Print Signal Sequence 2-3 2.1.3 Print Driving 2-4 BlockNo. Printheadnozzle No. F-2-3 Thepattern is repeated until 2560 nozzles is reached. 2-5 Chapter 2 2-6 2.2 Firmware 2.2.1 Operation Sequence at Power-on 2-7 2.2.2 Operation Sequence at Power-off 2-8 2.2.3 Print Control Printing Modes 2-9 2-10 2-11 2-12 2-13 2-14 2.2.4 Print Position Adjustment Function 2.2.5 Head Management 2.2.6 Printhead Overheating Protection Control 2-15 2.2.7 Pause between Pages 2.2.8 White Raster Skip 2.2.9 Sleep Mode 2-16 2.3 Printer Mechanical System 2.3.1 Outline 2.3.1.1 Outline 2-17 2.3.2 Ink Passage 2.3.2.1 Ink Passage 2-18 2-19 2.3.2.2 Ink Tank Unit 2-20 F-2-9 2-21 2-22 2.3.2.3 Carriage Unit 2-23 2-24 2-25 2.3.2.4 Printhead 2-26 2.3.2.5 Purge Unit Resin Sillicon plate Heater Shared ink chamber Heater 2-27 Details of the cleaning function are shown in the table below. Chapter 2 2-28 Cleaning operation timings are as follows. 2-29 *1: Quantities of ink consumption by nozzle train 2-30 2-31 Advance notice of replacement 47,500times Service call 50,000times 2-32 2.3.2.6 Maintenance Cartridge 2-33 2.3.2.7 Air Flow 2.3.3 Paper Path 2.3.3.1 Outline 2-34 2-35 2.3.3.2 Paper Path Page 2-37 2.4 Printer Electrical System 2.4.1 Outline 2.4.1.1 Overview 2-38 F-2-25 2-39 2.4.2 Main Controller 2.4.2.1 Main controller components 2-40 2-41 2.4.3 Carriage Relay PCB 2.4.3.1 Carriage relay PCB components 2.4.4 Head Relay PCB 2.4.4.1 Head relay PCB components 2-42 2.4.5 Maintenance Cartridge Relay PCB 2.4.5.1 Maintenance cartridge relay PCB components 2.4.6 Power Supply 2.4.6.1 Power supply block diagram 2-43 2.5 Detection Functions with Sensors 2.5.1 Sensors for covers 2-44 2.5.2 Ink passage system 2-45 2-46 2-47 2.5.3 Carriage system 2-48 2-49 2.5.4 Paper path system Page 3-1 3.1 Transporting the Printer 3.1.1 Transporting the Printer 3.1.1.1 Transporting the Printer 3-2 3-3 3-4 3.1.2 Reinstalling the Printer 3.1.2.1 Reinstalling the Printer Page Page 4.3 Points to Note on Disassembly and Reassembly........................................ 4-3 Page Chapter 4 F-4-2 4-2 Printer SymbolMeanings c: Connector,e: E-ring, h: Holder, s: Screw 4-3 4.3 Points to Note on Disassembly and Reassembly 4.3.1 Note on locations prohibited from disassembly 4.3.2 Moving the carriage manually 4.3.3 Units requiring draining of ink 4-4 4.3.4 External Covers Page 4-6 4-7 4-8 4-9 4-10 4-11 4.3.5 Waste Ink Box 4-12 4.3.6 Driving Unit 4-13 4.3.7 Ink Tube Unit 4-14 4-15 4-16 4.3.8 Carriage Unit 4-17 4-18 4-19 4-20 4-21 4.3.9 Feeder Unit 4-22 4.3.10 Purge Unit 4-23 4.3.11 Ink Tank Unit Page 4-25 4.3.12 Head Management Sensor 4-26 4.3.13 Multi Sensor 4-27 4.3.14 PCBs 4-28 4.3.15 Opening the Cap/Moving the Wiper Unit 4-29 4.3.16 Opening/Closing the Ink Supply Valve 4-30 4.3.17 Draining the Ink 4-31 4.4 Applying the Grease 4.4.1 Applying the Grease Chapter 4 4-32 F-4-41 F-4-42 4.5 Adjustment and Setup Items 4.5.1 Adjustment Item List 4.5.2 Procedure after Replacing the Feed Roller or Feed Roller Encoder 4.5.3 Procedure after Replacing the Carriage Unit or Multi Sensor 4-34 4.5.4 Procedure after Replacing the Head Management Sensor Page Page 5-1 5.1 Periodic Replacement Parts 5.1.1 Periodic Replacement Parts 5.2 Consumable Parts 5.2.1 Consumable Parts Level Periodic Replacement part User None Service Personnel None 5.3 Periodic Maintenance 5.3.1 Periodic Maintenance Page Page 5-5 Page Page 6-1 6.1 Troubleshooting 6.1.1 Outline 6.1.1.1 Outline of Troubleshooting 6-2 6.2 Location of Connectors and Pin Arrangement 6.2.1 Main controller PCB 6-3 6-4 6-5 6-6 6-7 6-8 6-9 6-10 6-11 6-12 6.2.2 Carriage relay PCB 6-13 6-14 6-15 6-16 6-17 6-18 6-19 6.2.3 Head relay PCB 6-20 6-21 6-22 6-23 6-24 6.3 Version Up 6.3.1 Firmware Update Tool 6-25 6.4 Service Tools 6.4.1 Tool List Page Page Page 7-1 7.1 Service Mode 7.1.1 Service Mode Operation 7.1.2 Map of the Service Mode Page Page Page Page Page Page Page 7-10 7.1.3 Details of Service Mode 7-11 7-12 7-13 7-14 7-15 7-16 7-17 7-18 7-19 7-20 7-21 7-22 7-23 7-24 7-25 7-26 7-27 7.1.4 Sample Printout F-7-1 (1) (2) (3) (a) (b) (c) (d) (e) (f) 7-28 Nozzle Check Pattern SERVICE 7-29 Chapter 7 7-30 F-7-5 7-31 F-7-6 7-32 7.2 Special Mode 7.2.1 Special Modes for Servicing 7-33 Page Page 8.1 Outline 8.1.1 Outline 8-2 8.2 Warning Table 8.2.1 Warnings 8-3 8.3 Error Table 8.3.1 Error Code List 8-4 8-5 8-6 8.4 Sevice Call Table 8.4.1 Service call errors Page Main controller PCB (1/3) Carriage relay PCB (1/2) General Circuit Diagram (2/4) F-1-2 Main controller PCB (2/3) General Circuit Diagram (3/4) F-1-3 Main controller PCB (3/3)