Canon 2160B002 1-45, 1.7.2.2 Ink Tank

Chapter 1

1-45

b. Capping action

The printer performs a capping action at the end of printing or when it stands by in the wake of an error

occurrence, to protect the printhead and prevent ink leaks.

If the printer has been powered off by inadvertently disconnecting the power cord from the wall outlet,

reconnect the power cord to the wall out and turn on the power key. When the printer starts up successfully

to enter online or offline mode, turn off the power key.

Failure to perform a capping action successfully could result in problems, such as printhead nozzles clogged

by a dried ink or inks leaking from the printhead.

c. When leaving the printer of service

Even when the printer is out of service, store it with the printhead mounted on it.

Leaving the printer with the printhead removed from it could allow foreign matter to adhere to the printhead

or dry an ink, resulting in clogged nozzles to cause print defects.

If the printhead is drained of inks for shipping purposes even though it is kept mounted on the printer, the

nozzles could dry, resulting in print defects.

d. Ink conductivity

The inks used are conductive. If an ink is found to leak to the mechanical assembly, wipe it off with a soft

cloth moistened with water and wrung thoroughly. If an ink is found to leak to the electrical assembly, blot

it with tissue paper or the like and wipe it off thoroughly. If wiping off a leaking ink thoroughly is difficult,

replace with a new component.

Energizing the printer with the electrical assembly being wetted with an ink could cause damage to it.

Never connect the power cord to the wall outlet while the electrical assembly is wet with an ink.

1.7.2.2 Ink Tank

0012-6229

a. Opening ink tanks

Do not unpack ink tanks until they are ready for immediate use.

When placing an ink tank in position, shake it slowly seven to eight times before opening it. Without

shaking, the ingredients of the ink might settle, resulting in degraded print quality.

Once an ink tank is opened, mount it in the printer promptly to prevent any foreign matter from sticking to

the ink port.

b. Handling ink tanks

Contents

Main Page Symbols Used Symbol Description Page Page Page Page Page Page Page 1.5 Names and Functions of Components........................................................ 1-18 1.1 Product Overview 1.1.1 Product Overview 1-2 1.2 Features 1.2.1 Features 1.2.2 Printhead 1-3 1.2.3 Ink Tank 1.2.4 Cutter unit 1.2.5 Roll Holder 1-4 1.2.6 Stand [A] [B] 1-5 1.2.7 IEEE1394 (FireWire) Board 1.2.8 Consumables Page 1-7 1.3 Product Specifications 1.3.1 Product Specifications 1-8 1-9 1-10 1.4 Detailed Specifications 1.4.1 Print Speed and Direction 1-11 Plain Paper/ Recycled Paper 1-12 1-13 1-14 1-15 1-16 1-17 1.4.2 Interface specifications 1-18 1.5 Names and Functions of Components 1.5.1 Front 1-19 1.5.2 Rear 1-20 1.5.3 Carriage 1-21 1.6 Basic Operation 1.6.1 Operation Panel 1-22 1.6.2 Main Menu 1-23 1-24 1-25 1-26 1-27 1-28 1-29 1-30 1-31 1-32 Setting Item 1-33 Setting Item 1-34 1-35 press the[ ] button. Choose [OK] to restore the network settings to the default values. 1-36 1-37 1-38 1-39 1-40 1.7 Safety and Precautions 1.7.1 Safety Precautions 1.7.1.1 Moving Parts 1-41 1.7.1.2 Adhesion of Ink 1-42 1.7.1.3 Electric Parts 1-43 1-44 1.7.2 Other Precautions 1.7.2.1 Printhead 1-45 1.7.2.2 Ink Tank 1-46 1.7.2.3 Handling the Printer 1-47 1-48 1.7.3 Precautions When Servicing Printer 1.7.3.1 Notes on the Data Stored in the Printer 1.7.3.2 Confirming the Firmware Version 1.7.3.3 Precautions against Static Electricity Page Page Page Page 2-1 2.1 Basic Operation Outline F-2-1 2.1.1 Printer Diagram Shown below is a printer diagram. Chapter 2 2.1.2 Print Signal Sequence 2-3 2.1.3 Print Driving 2-4 BlockNo. Printheadnozzle No. F-2-3 Thepattern is repeated until 2560 nozzles is reached. 2-5 Chapter 2 2-6 2.2 Firmware 2.2.1 Operation Sequence at Power-on 2-7 2.2.2 Operation Sequence at Power-off 2-8 2.2.3 Print Control Printing Modes 2-9 2-10 2-11 2-12 2-13 2-14 2.2.4 Print Position Adjustment Function 2.2.5 Head Management 2.2.6 Printhead Overheating Protection Control 2-15 2.2.7 Pause between Pages 2.2.8 White Raster Skip 2.2.9 Sleep Mode 2-16 2.3 Printer Mechanical System 2.3.1 Outline 2.3.1.1 Outline 2-17 2.3.2 Ink Passage 2.3.2.1 Ink Passage 2-18 2-19 2.3.2.2 Ink Tank Unit 2-20 F-2-9 2-21 2-22 2.3.2.3 Carriage Unit 2-23 2-24 2-25 2.3.2.4 Printhead 2-26 2.3.2.5 Purge Unit Resin Sillicon plate Heater Shared ink chamber Heater 2-27 Details of the cleaning function are shown in the table below. Chapter 2 2-28 Cleaning operation timings are as follows. 2-29 *1: Quantities of ink consumption by nozzle train 2-30 2-31 Advance notice of replacement 47,500times Service call 50,000times 2-32 2.3.2.6 Maintenance Cartridge 2-33 2.3.2.7 Air Flow 2.3.3 Paper Path 2.3.3.1 Outline 2-34 2-35 2.3.3.2 Paper Path Page 2-37 2.4 Printer Electrical System 2.4.1 Outline 2.4.1.1 Overview 2-38 F-2-25 2-39 2.4.2 Main Controller 2.4.2.1 Main controller components 2-40 2-41 2.4.3 Carriage Relay PCB 2.4.3.1 Carriage relay PCB components 2.4.4 Head Relay PCB 2.4.4.1 Head relay PCB components 2-42 2.4.5 Maintenance Cartridge Relay PCB 2.4.5.1 Maintenance cartridge relay PCB components 2.4.6 Power Supply 2.4.6.1 Power supply block diagram 2-43 2.5 Detection Functions with Sensors 2.5.1 Sensors for covers 2-44 2.5.2 Ink passage system 2-45 2-46 2-47 2.5.3 Carriage system 2-48 2-49 2.5.4 Paper path system Page 3-1 3.1 Transporting the Printer 3.1.1 Transporting the Printer 3.1.1.1 Transporting the Printer 3-2 3-3 3-4 3.1.2 Reinstalling the Printer 3.1.2.1 Reinstalling the Printer Page Page 4.3 Points to Note on Disassembly and Reassembly........................................ 4-3 Page Chapter 4 F-4-2 4-2 Printer SymbolMeanings c: Connector,e: E-ring, h: Holder, s: Screw 4-3 4.3 Points to Note on Disassembly and Reassembly 4.3.1 Note on locations prohibited from disassembly 4.3.2 Moving the carriage manually 4.3.3 Units requiring draining of ink 4-4 4.3.4 External Covers Page 4-6 4-7 4-8 4-9 4-10 4-11 4.3.5 Waste Ink Box 4-12 4.3.6 Driving Unit 4-13 4.3.7 Ink Tube Unit 4-14 4-15 4-16 4.3.8 Carriage Unit 4-17 4-18 4-19 4-20 4-21 4.3.9 Feeder Unit 4-22 4.3.10 Purge Unit 4-23 4.3.11 Ink Tank Unit Page 4-25 4.3.12 Head Management Sensor 4-26 4.3.13 Multi Sensor 4-27 4.3.14 PCBs 4-28 4.3.15 Opening the Cap/Moving the Wiper Unit 4-29 4.3.16 Opening/Closing the Ink Supply Valve 4-30 4.3.17 Draining the Ink 4-31 4.4 Applying the Grease 4.4.1 Applying the Grease Chapter 4 4-32 F-4-41 F-4-42 4.5 Adjustment and Setup Items 4.5.1 Adjustment Item List 4.5.2 Procedure after Replacing the Feed Roller or Feed Roller Encoder 4.5.3 Procedure after Replacing the Carriage Unit or Multi Sensor 4-34 4.5.4 Procedure after Replacing the Head Management Sensor Page Page 5-1 5.1 Periodic Replacement Parts 5.1.1 Periodic Replacement Parts 5.2 Consumable Parts 5.2.1 Consumable Parts Level Periodic Replacement part User None Service Personnel None 5.3 Periodic Maintenance 5.3.1 Periodic Maintenance Page Page 5-5 Page Page 6-1 6.1 Troubleshooting 6.1.1 Outline 6.1.1.1 Outline of Troubleshooting 6-2 6.2 Location of Connectors and Pin Arrangement 6.2.1 Main controller PCB 6-3 6-4 6-5 6-6 6-7 6-8 6-9 6-10 6-11 6-12 6.2.2 Carriage relay PCB 6-13 6-14 6-15 6-16 6-17 6-18 6-19 6.2.3 Head relay PCB 6-20 6-21 6-22 6-23 6-24 6.3 Version Up 6.3.1 Firmware Update Tool 6-25 6.4 Service Tools 6.4.1 Tool List Page Page Page 7-1 7.1 Service Mode 7.1.1 Service Mode Operation 7.1.2 Map of the Service Mode Page Page Page Page Page Page Page 7-10 7.1.3 Details of Service Mode 7-11 7-12 7-13 7-14 7-15 7-16 7-17 7-18 7-19 7-20 7-21 7-22 7-23 7-24 7-25 7-26 7-27 7.1.4 Sample Printout F-7-1 (1) (2) (3) (a) (b) (c) (d) (e) (f) 7-28 Nozzle Check Pattern SERVICE 7-29 Chapter 7 7-30 F-7-5 7-31 F-7-6 7-32 7.2 Special Mode 7.2.1 Special Modes for Servicing 7-33 Page Page 8.1 Outline 8.1.1 Outline 8-2 8.2 Warning Table 8.2.1 Warnings 8-3 8.3 Error Table 8.3.1 Error Code List 8-4 8-5 8-6 8.4 Sevice Call Table 8.4.1 Service call errors Page Main controller PCB (1/3) Carriage relay PCB (1/2) General Circuit Diagram (2/4) F-1-2 Main controller PCB (2/3) General Circuit Diagram (3/4) F-1-3 Main controller PCB (3/3)