38VYX110/38VYX130

Selection of installation

Installation Place

•A place which provides a specified space around the outdoor unit.

•A place where the operation noise and discharged air are not given to your neighbors.

•A place that is not exposed to a strong wind.

•A place that does not block a passage.

•When the outdoor unit is installed in an elevated position, be sure to secure its feet.

•There must be sufficient space for carrying in the unit.

•A place where the drain water does not make any problem.

•If the unit is installed in areas where heavy snowfalls may occur, it is necessary to raise its level at least 200 mm above the usual snow level.

•The support must be suitable for the unit weight.

CAUTION:

•Install the outdoor unit at a place where discharge air is not blocked.

•When an outdoor unit is installed in a place that is always exposed to a strong wind like a coast or on a high storey of a building, secure a normal fan operation by using a duct or a wind shield

•When installing the outdoor unit in a place that is constantly exposed to a strong wind such as the upper stairs or rooftop of a building, apply the windproof measures referring to the following examples.

•Install the unit so that its discharge port faces the wall of the building. Keep a distance 500 mm or more between the unit and the wall surface.

•Supposing the wind direction during the operation season of the air conditioner, install the unit so that the discharge port is set at right angle to the wind direction.

•Installation in the following places may result in some troubles. Do not install the unit in such places below.

•A place full of machine oil.

•A place full of sulphuric gas.

•A place where high-frequency radio waves are likely to be generated as from audio equipment, welders, and medical equipment.

Strong wind

Cover knockout for pipe connection

Knockout procedure

•The indoor/outdoor connecting pipes can be connected to 4 directions.

Take off the knockout part of the pipe cover in which pipes or wires pass through the base plate.

•As shown in the figure, do not remove the pipe cover from the cabinet so that the knockout hole can be easily punched.

To knock out, punch the 3 connected parts with a screwdriver and remove the pipe cover by hand.

•After marking the knockout hole, remove the burr and mount the attached protective bush and guard material for pass-through part in order to protect pipes and wires.

•After connecting the pipes, be sure to mount the pipe cover. The pipe cover is easily mounted by cutting off the slit at the lower part of the cover.

How to remove the front panel

1.Remove screws of the front panel.

2.Pull the front panel downward.

Removing the front panel, the electric parts appear at the front side.

•The power supply cables can be inserted into the pipe holes. Enlarge the pipe holes if they are too small.

•The power supply cable and the indoor/outdoor connecting cable must be fixed by means of the strip on the connection fixing bracket so that they are not in contact with the compressor and the hot pipes.

To ensure good tensile strength, the electric cables must be fastened using the cable-holder on the plate.

Strip

Rear direction Pipe cover Side direction Down direction Front direction

Electric parts box Fixing plate Piping hole Cable-holder for electric cables Front panel

GB - 4

Page 4 Page 6
Page 5
Image 5
Carrier 38VYX130 Installation Place, Cover knockout for pipe connection Knockout procedure, How to remove the front panel
Page 4 Page 6

38VYX110, 38VYX130 specifications

The Carrier 38VYX130 and 38VYX110 are advanced air conditioning units designed for residential and light commercial applications, offering optimal energy efficiency, reliable performance, and enhanced comfort. These models exemplify Carrier's commitment to delivering high-quality climate control solutions.

One of the standout features of the Carrier 38VYX series is its energy efficiency. Both the 38VYX130 and 38VYX110 boast a high Seasonal Energy Efficiency Ratio (SEER) rating, indicating their ability to provide effective cooling while consuming less energy. This makes them an environmentally friendly option, as well as a cost-effective choice for homeowners and businesses looking to reduce their energy bills.

The 38VYX130 and 38VYX110 utilize inverter technology, which allows the compressor to adjust its speed based on the cooling demand. This not only enhances energy efficiency but also ensures consistent comfort levels by minimizing temperature fluctuations. This feature is particularly beneficial in variable weather conditions, providing a stable indoor climate without excessive energy consumption.

Another significant technological advancement in these models is the use of R-410A refrigerant, which is known for its low environmental impact compared to traditional refrigerants. This aligns with Carrier's commitment to sustainability and reducing the carbon footprint of their products. Additionally, both units are equipped with advanced filtration systems that help improve indoor air quality by capturing dust, allergens, and other airborne particles.

The Carrier 38VYX series is also designed with quiet operation in mind. With sound levels that fall within the low dB range, these units ensure that homeowners can enjoy a comfortable living environment without disruptive noise, whether the system is running during the day or at night.

For ease of installation and maintenance, the 38VYX130 and 38VYX110 come with user-friendly features, including a compact design that allows for flexible placement and service access. Furthermore, Carrier offers a robust warranty and customer support, ensuring peace of mind for users.

In conclusion, the Carrier 38VYX130 and 38VYX110 are exceptional choices for those looking for efficient, reliable, and quiet air conditioning systems. With their advanced technologies and commitment to sustainability, these models are set to provide superior comfort for years to come.
Top Page Image Contents