Carrier ERVCCSHB1100 Operation, Humidity Selector, OneTouch Control, Recommended Humidity Levels

between wall control and ERV/HRV connector following color code. (See Fig. 5 and 10.) Replace top cover assembly.

NOTE: ERV/HRV wall control and circuit board operate on 12VDC.

		YELLOW
		RED
		GREEN
		BLACK
Y	R	GB

A98383

Fig. 10 - Typical Wall Control

Operation

The Standard and Latent wall controls have 4 basic modes of operation, OFF, LOW, HIGH, and INTERMITTENT. Be sure that all modes of operation are fully functional. See Table 1 indicating standard control operation.

1.With switch off, ERV/HRV is inoperative and the LED is out.

2.With switch on LOW, ERV/HRV continuously exchanges air with outside. If control is satisfied, blower will run in low speed, otherwise, blower will run on high speed. The LED is illuminated all the time.

3.With switch on INTERMITTENT, the ERV/HRV ex- changes air with outside on high-speed blower, and unit shuts down when control is satisfied. The ON LED is illu- minated all the time, and AIR EXCHANGE LED is illumi- nated only when unit is running.

Humidity Selector

The humidity selector is a built-in control designed to properly control the level of humidity in the house during the winter and summer months. This control helps avoid condensation problems in upper northern regions where indoor humidity is a problem during the winter season.

NOTE: This control is not to be confused with a dehumidistat used during the summer months to control high relative indoor humidity.

Table 2 recommends humidity levels to avoid condensation.

Table 2 – Recommended Humidity Levels

OUTSIDE	DOUBLE---PANE	TRIPLE---PANE
TEMPERATURE	WINDOWS	WINDOWS
50°F / 10°C	55%	65%
32°F / 0°C	45%	55%
14°F / --- 10°C	35%	45%
--- 4°F / --- 20°C	30%	45%
--- 22°F / --- 30°C	25%	35%

OneTouch Control

The OneTouch Control can be used as the primary wall control for the ERV/HRV. This control will step through the modes of operation with consecutive presses of the button. The LED indicates which mode is currently selected, Off, Intermittent, Low, or High.

NOTE: OneTouch Control does not have a humidity selector.

NOTE: OneTouch Intermittent mode exchanges air on low speed for 20 minutes per hour.

Latent Control

NOTE: For Latent Controls used with ERV;s, to ensure highest degree of humidity control in cooling season, the INTERMITTENT mode should be used.

Integrated Control

All units are equipped with an integrated control, located under the unit, in front of the electrical compartment. Use the push button (1) to control the unit. The LED (2) will then shows on which mode the unit is in. Integrated Control overrides Wall Control function. When LED is off, ventilator responds to Wall Control command. See Fig. 11.

WARNING	AVERTISSEMENT
Risk of electric shock. Before performing	Danger d’électrocution. Débranchez
any maintenance or servicing, always	toujours l’appareil avant d’entreprendre
disconnect the unit from its power source.	des travaux d’entretien ou de réparation.

	CAUTION	ATTENTION
	Unscrew both screws to open the electrical	Dévisser les deux vis pour ouvrir le compartiment
	compartment. To completely remove, detach	électrique. Pour retirer complètement, le
	from its retention wire inside.	détacher de son fil de rétention intérieur.
No light	OFF or remote controled
Amber light	LOW speed
Green ligh	HIGH speed
Blinking light	See User Manual
Sans lumière	Arrêté ou contrôlé
	par contrôle mural
Lumière ambre	Basse vitesse
Lumière verte	Haute vitesse
Clignotant	Voir guide d’utilisation

1 2

A07260

Fig. 11 - Integrated Control

Refer to table below to see how to operate the unit using its integrated control.

PRESS ON PUSH	LED COLOR	RESULTS
BUTTON
Once	Amber	Unit is on Low
		Speed
Twice	Green	Unit is on High
		Speed
Three Times	No Light	Unit is OFF

If a problem occurs during the unit operation, its integrated control LED (2) will blink. The color of the blinking light depends on the type of error detected. Refer to Troubleshooting for further details.

NOTE: The ERV/HRV may be controlled using the Infinity system control. The ERV/HRV may be connected using either a NIM or a 4-Zone Damper Module. See the appropriate instructions if using the NIM or a 4-Zone Damper Module for connection instructions.

The Infinity system control will simultaneously control the ERV/HRV and the indoor blower.

Push Button Timers may be used and are connected to the ERV/HRV. However, the Infinity system should be set to continuous fan to ensure that the fresh air is circulated in the home. In a Zoned System, at least one zone should be set to continuous fan.

ERV / HRV

5