Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death.
Do not allow children
to operate the Door Control or remote control
transmitter(s).
A moving garage door could injure or kill
someone under it.
Activate the opener only
when you can see the door clearly, it is free of
obstructions, and is properly adjusted.
WARNING
SECURITY✚3-Channel Remote Control Programming (OPTIONAL)
26
NOTICE: To comply with FCC/IC rules, adjustment or modifications of this receiver
and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THEREARE NO OTHERUSER SERVICEABLE PARTS.
The 90 Series remote control (with yellow battery test
light) works only with door openers and light controls
having an orange “Smart” button and a yellow indicator
light.
Programming instructions are described and illustrated
below. The additional push buttons can also activate
other garage door openers and/or light controls.
(Instructions for programming light products are included
with those accessories.) See Accessories on page 34.
Your SECURITY✚opener will operate with:
• several SECURITY✚remote controls (with yellow
indicator lights) utilizing up to 8 functions.
NOTE:
Open/Close/Stop operation counts as 1 function.
• one Keyless Entry System (with SECURITY✚logo)
To Program the Opener to Accept
the Remote Control Code
Select a remote control push button to operate the
opener. The
large
button is recommended for use with
a garage door opener.
1. Press and
hold
the selected remote control push
button. See Figure 1.
2. Press and release the “Smart” (learn) button on the
opener panel, Figure 2. The indicator light on the
panel will begin to blink and the opener light will
flash once.
3.
Release the remote push button.
Now the opener will operate when that remote control
button is pressed. Test it by pressing the remote button
to see that the door goes up and down.
Adding a remote can also be done from the Multi-
Function Door Control, as follows:
1.
With the door closed,
press and hold a remote push
button.
2. Press and hold the Light button on the door control.
3. Press and hold the door control push bar.
4. After the opener light flashes, release all buttons.
Test by pressing the remote push button.
To Erase All Remote Control Codes
Press and hold the “Smart” button on the opener panel
until the indicator light turns off (about 6 seconds). All
transmitter codes are now erased. Then follow the
steps above to re-program each remote control.
To Control the Opener Light
With SECURITY✚transmitters, a remote push button
can be programmed to operate the opener light without
opening the door.
1.
With the door closed,
press and hold the remote
button that you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener light flashes, release all buttons.
Test by pressing the remote push button. The opener
light should turn on or off but the door should not move.
SECURITY✚
Garage Door Opener
BACK PANEL
"Smart" (learn)
Button Indicator Light
KG KG
1
3
9
7
5
1
3
9
7
5
123
Figure 2
Select a
push button
Yellow
Battery Indicator
Light
Model 96LM
SECURITY✚Remote Control
Code programming instructions are
also located on the opener panel.
Open/Close/Stop Operation
The SECURITY✚remote control can be programmed
to operate one door using all 3 buttons: the large
button will only open the door, the middle button will
only close the door, and the third button will stop the
door’s movement. You may set up this feature as
follows:
1.
With the door closed,
press and hold
the large remote push button.
2. Press and hold the Lock button
on the door control.
3. Press and hold the door control push bar.
When the opener light flashes, release all buttons. Test
by pressing the large
(Open)
button on the remote.
The door should open. Press it again while the door is
open and nothing should happen. Press the middle
(Close)
button and the door should close. Press the
third
(Stop)
button while the door is moving and it
should stop immediately.
Open
Close
Stop