Chamberlain ATS211R Opener Carton Inventory

5

Straight

Door Arm

Door Bracket Plate

Door Bracket

Safety Labels

and

Literature

"C" Wrap (2)

2 -Conductor Bell Wire

White & White/Red

Curved Door Arm

Rail

Styrofoam

Chain

Pulley Bracket

Trolley

Chain

Safety Reversing Sensor

Mounting Bracket

With Slot (2)

Safety Reversing Sensor

Mounting Bracket

With Square Holes (2)

Mounting Hardware

(Rail Support Bracket)

Header Bracket with

Clevis Pin and Fastener

UP

CEILING MOUNT ONLY

Lighted Door

Control Button

(2) Safety Reversing Sensors

(1 Sending Eye and 1 Receiving Eye)

with

2-Conductor White & White/Black Bell Wire

attached

Rail Support

Bracket

Opener Carton Inventory

Your garage door opener is packaged in two cartons which contain all parts illustrated below. If anything is

missing, carefully check the packing material. Parts may be "stuck" in the foam. Hardware for assembly and

installation is listed below.

Assembly Hardware

5/16"-18x1/2" Washered Screw,

(2) (Mounted in Opener)

1/4"-20x5/8" Hex Screw (2)

1/4"-20x5/8" Lock Washer (2)

#8-32x3/8" Screw (1)

5/16"-18x1/2" Washered Screw (2)

Installation Hardware

Hex Screw 5/16"-18x7/8" (4)

Nut 5/16"-18 (4)

Lock Washer 5/16" (4)

Rail Grease

Lag Screw 5/16"-9x1-5/8" (2)

Lag Screw 5/16"-18x1-7/8" (2)

Screw 6ABx1-1/2" (2)

Handle

Ring Fastener (3)

Self-Threading Screw 1/4"-14x5/8"

Insulated Staples (10)

Dry Wall Anchors (2)

Clevis Pin 5/16"x2-3/4" (1)

Clevis Pin 5/16"x1" (2)

Rope

Hardware for Safety Reversing

Sensor

Lag Screw 1/4x1-1/2" (4)

Carriage Bolt 1/4"-20x1/2" (4)

Lock Nut 1/4"-20 (4)

Wing Nut (2)

Hex Screw 1/4-20x1-1/2" (2)

Screw #10-32x3/8" (4)

Lock Nut #10x32 (4)

Insulated Staples (20)

Hardware Inventory

Contents

Main TM UP FORCE DOWN FORCE MODEL ATS 211R COMMERCIAL DOOR OPENER For Residential and Light Duty Commercial Use Install on Sectional Doors Only OWNER'S MANUAL Start by reviewing these important safety alert symbols serious injuries or death Read the instructions carefully. Mechanical Electrical You'll Need Tools Before you begin, survey your garage area. Do any of the following conditions apply to you? If your door has extension springs, the opener must be installed in the center of the door. Opener Carton Inventory Hardware Inventory CAUTION! Use only the screw previously removed from opener. Assembly Section: Pages 6 7 Use only these screws! Assembly Step 1 Attach the Rail to the Opener Assembly Step 2 IMPORTANT INST ALLATION INSTRUCTIONS To reduce the risk of severe injury or death to persons: An improperly balanced door may not reverse and could result in severe injury or death. Ropes connected to a garage door can cause entanglement and death. Installation Section: Pages 8 20 Installation Step 1 Determine Header Bracket Location The door might not reverse when required, and could cause serious injury or death. Fasten the Header Bracket to the Wall Fasten the Header Bracket to the Ceiling Installation Step 2 Install the Header Bracket Installation Step 3 Attach the Rail to the Header Bracket Installation Step 4 Position the Opener Installation Step 5 Hang the Opener each The opener could fall and injure someone if it is not properly secured. Installation Step 6 Install the Door Control The garage door could close and cause serious injury or death. but where the garage door is visible. A moving garage door could injure someone under it. Installation Step 7 Install the Light Installation Step 8 Attach the Manual Release Rope and Handle The rope knot could become untied and you could fall. Installation Step 9 Electrical Requirements and If permanent wiring is required by your local code, refer to the following procedure: To prevent electrocution or fire, The Protector System must Information you'll need before you begin the installation of the safety reversing sensor. Installation Step 10 Install the Safety Reversing Sensor (Receiving and Sending Eyes) Figure 4 Figure 5 Hardware Shown Actual Size Figure 6 receiving eye glows steadily sending eye glows steadily, CAUTION Fasten Door Bracket & Plate AVERTISSEMENT INSTALLATION STEP 11 Fasten the Door Bracket Installation Step 12 Connect Door Arm to Trolley Hole Alignment Alternative above cut end down Adjustment Step 1 Adjust the UP and DOWN Limits How and When to Adjust the Limits Adjustment Section: Pages 21 23 Adjustment Step 2 Adjust the Force up stops nuisance reversals Adjustment Step 4 Test the Safety Reverse System Adjustment Step 3 Test The Protector System Limit and Force Adjustment Control IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of severe injury or death to persons: must Care of Your Opener Failure to properly adjust the opener may result in severe injury or death. Weak or broken springs may cause the door to fall rapidly, causing injury or death to persons. Operation of Your Opener Operation of the Door Control Button stop Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. SECURITY3-Channel Remote Control Programming (OPTIONAL) NOTE: Open/Close/Stop operation counts as 1 function. Figure 1 flash once. 3. SECURITY Garage Door Opener SECURITYMulti-Function Door Control - Model 58LM (OPTIONAL) Operation of the Multi-Function Door Control Panel reverse To Turn Off: To Activate: SECURITYMulti-Function Door Control - Model 68LM (OPTIONAL) Figure 1 Alternate Installation For pre-wired installations, For standard wall mount, SECURITYKeyless Entry - Model 67LM (OPTIONAL) hold With the door closed, Having a Problem? Situation Probable Cause & Solution Having a Problem? (continued) Situation Probable Cause & Solution Page Repair Parts Accessories Available for your Opener Other Products For Your Opener Index LIFTMASTER GARAGE DOOR OPENER ONE-YEAR LIMITED WARRANTY LIMITED WARRANTY ON MOTOR LIFTMASTER SERVICE IS ON CALL 1-800-528-2806 HOW TO ORDER REPAIR PARTS 1-800-528-2806 2001, The Chamberlain Group, Inc. 114A2296B All Rights Reserved Printed in Mexico