SECURITY✚Multi-Function Door Control - Model 68LM (OPTIONAL)
28
The Door Control Push Bar: Press to open or
close the door. Press again to
reverse
the door
during the closing cycle or to
stop
the door while
it's opening.
Light Feature: Press the Light button. If the opener
light is
off,
it will turn
on.
If the opener light is on, (even in the 4-1/2 minute
automatic cycle) it will turn
off.
But if you use the Light button to turn the light
on
and then activate the opener, the light will turn
off
after 4-1/2 minutes.
The Light Feature will not turn the opener light off
when the door is in motion.
Lock Feature: Designed to prevent operation of the
door from portable remote controls. However, the
door will
open
and
close
from the Door Control push
bar and from the Keylock and the Keyless Entry
Accessories.
To Activate:
Press and hold the Lock button for
2 seconds. The push bar indicator light will flash as
long as the Lock is
on
.
To Turn Off:
Press and hold the Lock button again
for 2 seconds. The indicator light will stop flashing.
Normal operation will resume. The Lock feature will
also turn off whenever the “Smart" button on the
opener end panel is activated.
Operation of the Multi-Function Door Control Panel
WARNING
2-Conductor
Bell Wire
2
1
Multi-Function
Door Control Panel
Terminal Screws
RED WHITE
Door Control
Push Bar
Light Button
Lock
Button
LOCK LIGHT
KG KG
1
3
9
7
5
1
3
9
7
5
23
1
Opener
Terminal
Screws
Antenna
Back Panel
of Opener
RED-1 WHT-2 BLK-3
NOTE: To ensure the proper functioning of your
new Garage Door Opener, remove all old or
previous push buttons/door control panels.
Locate the door control within sight of the door at
a minimum height of 5 feet where small children
cannot reach, and away from all moving parts of
the door and door hardware.
The multi-function door control panel is typically
attached directly to the wall,
Figure 1
. For pre-wired
installations (as in new home construction) it can be
mounted to a standard single gang box,
Figure 2
.
• Strip 1/4" of insulation from one end of the bell wire;
connect the wire to the two screw terminals on the
back of the door control panel as follows: white to 2
and white/red to 1. (NOTE: If “Lock” and “Light”
buttons do not function after completing
installation, reverse the connections.)
•
For standard wall mount,
fasten the door control
panel securely with 6ABx1-1/4" self-tapping screws.
Run the bell wire up the wall and across the ceiling
to the opener. Use insulated staples to secure the
wire in several places. Be careful not to pierce the
wire with a staple, thereby resulting in a short.
•
For pre-wired installations,
mount the door control
to the gang box with the 6-32x1" machine screws
provided.
• Connect the bell wire to the opener terminal screws
as follows: white to 2 and white/red to 1.
DO NOT CONNECT TO LIVE ELECTRICAL WIRING.
CONNECT ONLY TO 24 VOLT LOW VOLTAGE
WIRES. CONNECTION TO LIVE WIRES OR
HIGHER VOLTAGE MAY CAUSE SERIOUS INJURY
FROM SHOCK, BURN OR ELECTROCUTION.
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause serious
injury or death.
Install the door control (or any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware,
but where the garage door is visible.
Do not allow children to operate the push
button(s) or the remote control transmitter(s).
A moving garage door could injure someone
under it.
Activate the opener only when the
door is properly adjusted, you can see it clearly,
and there are no obstructions to door travel.
LOCK LIGHT
24 Volt
2-Conductor
Bell Wire
Figure 1
Standard Installation
Figure 2