SECURITY✚Keyless Entry - Model 67LM (OPTIONAL)
29
Features
For use with any SECURITY✚compatible garage door
opener receiver.
Personalized Code: Up to 10,000 possible
combinations. Code can be easily changed if desired.
Operation: 12 Volt power supply. Opener activates
when 4-digit code and Enter button is pressed.
If wrong numbers are accidentally pressed, correction
can be made immediately. The Enter button will transmit
only the last four digits.
The Keypad will blink for 15 seconds after the code is
transmitted. During that time the Enter button can be
used to stop or reverse the door travel.
A temporary entry code can be added for visitors or
service persons. This temporary code can be limited to a
programmable number of hours or a programmable
number of entries.
To comply with FCC/IC rules, adjustment or modification of receiver and/or transmitter
is prohibited, except for changing the code setting and replacing the transmitter battery.
THERE ARE NO OTHER USER SERVICEABLE PARTS.
Installation
Choose a
convenient
location for
installation. It
should be at eye
level, reachable
by the shortest
person who will
use it, and within
sight of the door.
For a one-piece
door, choose the
optional location shown in
the illustration to avoid injury
as the door swings out.
Open the keypad cover and
remove the battery
compartment screw and
cover. Take out the battery.
Hold keypad firmly with the
cover half open so both top
and bottom mounting holes
are visible. Use a punch to
mark each hole. Drill two
1/8" pilot holes. Fasten securely with screws provided.
Insert the plug provided into the top hole to cover the
fastening screw. Reinstall the battery, matching the +
and – markings on the battery compartment. Refasten
the compartment cover.
Changing the Personal Entry Code
Press the four buttons for the present personal entry
code, then press and hold the 0 button, then press
Enter.
The opener light will blink twice. Release the buttons.
Press the new 4-digit code you have chosen, then
press Enter.
The opener light will blink once when the code has
been learned.
Test by pressing the new code, then press Enter. The
door should move.
Door Jamb Edge
(Optional Location
for 1-Piece Door)
Keypad
Door Jamb Face
SECTIONAL DOOR ONLY
KEYPAD MUST BE INSTALLED
WITHIN SIGHT OF THE DOOR
Exterior Front Wall
1-Piece or
Sectional Door
Typical
Sectional Door
Installation
Setting the Personal Entry Code
We recommend that you program your personal
code now, before you install the Keyless Entry.
Then you can test the reception at the mounting
location before you proceed further.
1.Choose a 4-digit personal entry code using the
numbers from 0 to 9 (a number can be used more
than once, for example, 4,0, 4,1.)
2. Press the four buttons for the code, then press and

hold

the Enter button. The indicator light on the
door opener panel will blink.
3. Press and release the “Smart” button on the door
opener panel. After the opener light blinks, release
the Enter button.
Test by pressing the the code, then press Enter. The
door should begin to move.
You may also program the Keyless Entry from the
Multi-Function Door Control, as follows:
1.

With the door closed,

enter the four digit code
desired, then press and hold Enter.
2. Press and hold the light button on the door control.
3. Press and hold the door control push bar.
4. After the opener light blinks, release all buttons.
Plug
Battery
Cover
Battery
12
ABC
4
GHI
6
MNO
8
TUV
ENTER
0
3
DEF
5
JKL
7
PRS
9
WXY
Indicator
Light
Smart
Button
Garage Door Opener Receiver
(With Smart Button)
KG KG
1
3
9
7
5
1
3
9
7
5
123
Children operating or playing with a garage door
opener can injure themselves or others.
The garage
door could close and cause serious injury or death.
Do not allow children to operate the door push
button(s) or remote control(s).
A moving garage door could injure or kill someone
under it.
Activate the opener only when you can see
the door clearly, it is free of obstructions, and is
properly adjusted.
WARNING