INSTALLATION STEP 6

Install the Door Control

Locate the door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from all moving parts of the door and door hardware.

1.Strip 7/16" (11 mm) of insulation from one end of the bell wire. Connect it to the two screw terminals on the back of the door control by color: white wire to 2 and white/red wire to 1.

2.Fasten the Lighted Door Control Button securely with 6ABx1-1/2" screws. If installing into drywall, drill 5/32" holes and use the anchors provided.

3.Run the bell wire up the wall and across the ceiling to the opener. Use insulated staples to secure the wire in several places. Be careful not to pierce the wire with a staple, creating a short or open circuit.

4.Receiver terminal screws and the antenna are located on the back panel of the motor unit. Position the antenna wire as shown.

5.Connect the bell wire by color to the opener terminal screws: white to 2 and white/red to 1.

6.Use tacks or staples to permanently attach the entrapment warning label to the wall near the door control, and the manual release/safety reverse test in a prominent location on the inside of the garage door.

NOTE: DO NOT connect the power and operate the opener at this time. The trolley will travel to the full open position, but will not return to the close position until the sensor beam is connected and properly aligned. See Safety Reversing Sensor instructions beginning on page 15.

To prevent possible SERIOUS INJURY or DEATH from electrocution:

•Be sure power is not connected BEFORE installing door control.

•Connect ONLY to 24 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

•Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.

•NEVER permit children to operate or play with door control push buttons or remote control transmitters.

•Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

•ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.

HARDWARE SHOWN ACTUAL SIZE

 

Screw 6ABx1-1/2"

 

Insulated

Lighted Door Control Button

Drywall Anchors

Staples

Outside Keylock Accessory Connections

To opener terminal screws: White to 2 and white/red to 1.

TO PREVENT THE MOTOR PROTECTOR FROM TRIPPING, DO NOT EXCEED 8 DOOR OPERATIONS PER HOUR.

FASTEN LABEL ADJACENT TO DOOR

POUR ÉVITER QUE LE DISPOSITIF DE PROTECTION DU MOTEUR NE SE DÉCLENCHE, NE PAS FAIRE FONCTIONNER LA PORTE PLUS DE 8 FOIS PAR HEURE.

FIXER L'ÉTIQUETTE PRÈS DE LA PORTE.

132A2112A

 

2-Conductor

 

Bell Wire

WHT

 

-2

 

RED

Lighted

-1

 

Door Control

 

Terminal Screws

Opener

Terminal

Screws

2-Conductor Bell Wire

123

 

 

9

1

9

1

 

 

7

3

7

3

WARNING

 

 

5

 

5

 

 

KG

 

KG

 

 

 

 

 

 

Lighted

 

 

 

 

 

Door Control

 

 

 

 

 

Button

 

 

 

 

 

Back Panel

Antenna

 

 

Moving Door Can Cause

 

 

 

 

of Opener

 

 

 

 

Serious Injury or Death

 

 

 

 

 

Keep Clear! Door May Move at any Time

 

 

 

 

 

Without Prior Warning

 

 

 

 

 

Do Not Let Children Operate the Door or Play

 

 

 

 

 

in the Door Area

 

 

 

 

 

Keep Door in Sight at all Times When Door is Moving

 

 

 

 

 

12