Multi-Function Door Control (Optional)
INSTALLATION
Locate door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from moving parts of the door and door hardware. If installing into drywall, drill 5/32" holes and use anchors provided. For
1.Strip 1/4" (6 mm) of insulation from one end of bell wire and connect to the two screw terminals on back of door control by color: white wire to 2 and white/red wire to 1.
2.Remove cover by gently pushing both thumbs against upper corners of cover on back side of door control. Fasten with
•Drill and install bottom screw, allowing 1/8" (3 mm) to protrude above wall surface.
•Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.
•Install top screw with care to avoid cracking plastic housing.
DO NOT overtighten.
•Insert bottom tabs and snap on cover. (To remove cover after mounting, gently pry at top with paper clip or small flat head screwdriver.)
3.(Standard installation only) Run bell wire up wall and across ceiling to motor unit. Use insulated staples to secure wire in several places. Do not pierce wire with a staple, creating a short or open circuit.
4.Connect bell wire to the opener terminal screws: white to 2 and white/red to 1.
5.Use tacks or staples to permanently attach entrapment warning label to wall near door control, and manual release/safety reverse test label in a prominent location on inside of garage door.
NOTE: DO NOT connect the power and operate the opener at this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned. See Safety Reversing Sensor Instructions beginning on page 15.
To prevent possible SERIOUS INJURY OR DEATH from electrocution:
•Be sure power is not connected BEFORE installing door control.
•Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
•Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.
•NEVER permit children to operate or play with door control push buttons or remote control transmitters.
•Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
•ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.
OPERATION OF THE MULTI-FUNCTION DOOR CONTROL
Press the push button to open or close the door. Press again to reverse the door during the closing cycle or to stop the door while it’s opening.
Light feature | LOCK | Light |
LIGHT | ||
Press the Light button to turn the opener |
| Button |
|
| |
light on or off. It will not control the opener |
|
|
lights when the door is in motion. If you turn it on and then | ||
activate the opener, the light will remain on for |
Press again to turn it off sooner. The
A single blink indicates that the timer is reset to
Lock feature
Designed to prevent operation of the door from
To activate, press and hold the Lock button for 2 seconds. The push bar light will flash as long as the Lock feature is on.
To turn off, press and hold the Lock button again for 2 seconds. The push bar light will stop flashing. The Lock feature will also turn
off whenever the “learn” button on the motor unit panel is activated.
RED WHT
1 | 2 |
|
|
|
|
|
| |
Door Control Panel |
|
|
|
|
|
|
Terminal Screws |
|
|
|
|
|
|
|
| 1 | 2 |
|
| 3 |
Door Control |
|
|
|
|
|
|
Push Bar |
|
| 9 | 1 | 9 | 1 |
|
|
| 7 | 3 | 7 | 3 |
|
|
| 5 |
|
| 5 |
|
|
| KG |
|
| KG |
|
|
|
|
|
| |
Bell Wire |
|
|
|
|
|
|
Lock | LOCK |
|
|
|
|
|
LIGHT |
|
|
|
|
| |
Button |
|
|
|
|
|
|
| Light Button | Opener Panel |
| Antenna |
28