SLC 8DMT LEDs, Color Condition Indicated | Cisco Systems 6200

78-5296-02 10/02/98			Hardware Description 1
	Table 1-11	SLC 8DMT LEDs

	LED	Color	Condition Indicated

	POWER	Green	The SLC is receiving power.

	READY	Green	The SLC is experiencing no problems.
		Yellow	At least one port on the SLC is in line test mode.
		Off	The SLC is not communicating with the MPC. This is the case when
			• The SLC is initializing.
			• The SLC has a hardware problem. If the READY LED is off for an extended
			period when the POWER LED is on, see the Cisco 6200 User Guide for
			instructions on troubleshooting the SLC.

	PRIME	Green	The SLC is using the primary (A) bus to move information across the backplane.

	SEC	Green	The SLC is using the secondary (B) bus to move information across the backplane.
			(Redundant systems only.)

	Ports 0 to 7	Green	The following conditions exist:
			• The port is receiving good signal levels (no loss of signal, or LOS) from the CPE.
			• The port has frame alignment with the far end CPE (no loss of frame (LOF) or
			severely errored frames (SEC)).
			• The SLC has HEC alignment in the upstream direction.
			• The modems on both sides have negotiated the loop rates.
			The port LEDs remain lit (green) in the presence of occasional minor alarms.

		Flashing	The port is enabled and is trying to communicate with the remote CPE. (That is, the
		green	port is training or preparing to train.)

		Off	One of the following conditions exists:
			• The port is experiencing an intrusive DMT hardware test.
			• The port is disabled or is not conﬁgured.

Cisco 6200 User Guide

1-31

Image 31

Cisco Systems 6200 appendix SLC 8DMT LEDs, Color Condition Indicated

Contents

Cisco DSL Product Family Hardware Description Module Compartment Cisco 6200 Chassis Cisco 6200 Chassis, Front View Backplane Ethernet Management Bus Primary a and Secondary B H-BusesCisco 6200 Chassis, Rear View Connections to Pots Splitters or Telephone Lines Alarm Relay Connection Fan Tray Power Entry Modules PEMsPower Terminals Unused Connectors Dslam Speciﬁcations Cooling Vents Category Description Cisco 6200 Dslam SpeciﬁcationsSpeciﬁcation Description Standards and Certiﬁcations Network Trunk Cards NTCs What is the NTC OC-3? OC-3c Trunk Port NTC OC-3 Physical Description NTC OC-3 Faceplates Reset SwitchLED Indicators Describes the LEDs on the faceplate of the OC-3 NTC Color Condition Indicated LEDs on the NTC OC-3 NTC OC-3 Speciﬁcations What is the NTC STM-1?NTC OC-3 Speciﬁcations Lists the physical and electrical speciﬁcations of the NTC NTC STM-1 Application Trunk Port NTC STM-1 Physical Description NTC STM-1 Faceplates Describes the LEDs on the faceplate of the NTC STM-1 LEDs on the NTC STM-1 NTC STM-1 Speciﬁcations NTC STM-1 Speciﬁcations Management Processor Card MPCFunctional Description Cisco 6200 is controlled and managed by the MPC Physical Description ACO SwitchMPC Faceplate All LEDs on the MPC are described in Table Console PortPcmcia Slots and Ejection Buttons Ethernet Port Lists the physical and electrical speciﬁcations of the MPC MPC SpeciﬁcationsMPC Speciﬁcations Transmission Rates and Modem Training What is the SLC 8CAP?Subscriber Line Card SLC How the SLC Handles Trafﬁc 10 SLC 8CAP Operation Statistics Describes the LEDs on the faceplate of the SLC SLC 8CAP Physical DescriptionSLC 8CAP Faceplate SLC 8CAP LEDs SLC 8CAP Speciﬁcations SLC 8CAP Speciﬁcations How the SLC 8DMT Handles Trafﬁc What is the SLC 8DMT? Two modes are available for setting transmission rates SLC 8DMT Physical Description SLC 8DMT Faceplate 11 describes the LEDs on the faceplate of the SLC SLC 8DMT LEDs SLC 8DMT Speciﬁcations SLC 8DMT Speciﬁcations