Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware

About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems

Step 2 Attach the far end of the first E1 or T1 PRI telephony cable to the equipment that will connect with Cisco Unified MeetingPlace.

In many cases, the other equipment has an RJ-48c socket in which to plug the E1 or T1 PRI telephony cable. Alternately, the other equipment will be connected to a punchdown block. In this case, you will need to determine the block’s connection diagram and then connect to it with discrete wires from the cable.

Step 3 Plug the other end of the first E1 or T1 PRI telephony cable into the RJ-45 jack, labeled 1, on the far left of the front of the breakout box.

Step 4 Repeat Step 2 and Step 3 until all the E1 or T1 PRI telephony cables are connected to the breakout box.

Place the second, third, and fourth E1 or T1 PRI telephony cables, which correspond to the MP-MA-4-PRI, into the RJ-45 jacks labeled 2, 3, and 4. Place the remaining 16 E1 or T1 PRI telephony cables, which correspond to the MP-MA-16-PRI, into the 16 RJ-45 jacks on the front of the second breakout box. Start with the RJ-45 jack on the left and continue to the right.

Note The RJ-45 jacks labeled 5 to 16 in the first breakout box remain empty.

Step 5 Connect the trunk card cable assembly (50-pin Amphenol cable) for the first Multi Access Blade (the MP-MA-4-PRI) to the back of the first breakout box by securing the screws on both ends.

Looking at the back of the first breakout box, place the first trunk card cable assembly into the connector on the right.

Step 6 Connect the other end of the trunk card cable assembly (50-pin Amphenol cable) for the first

Multi Access Blade (the MP-MA-4-PRI) into the Multi Access Blade transition module by securing the screws on both ends.

Place the 50-pin Amphenol cable into the connector on the bottom, labeled spans 9 to 16.

Step 7 Repeat Step 5 and Step 6 for the trunk card cable assembly (50-pin Amphenol cable) for the second Multi Access Blade (the MP-MA-16-PRI).

Place the first trunk card cable assembly into the connector on the left side of the breakout box and on the top of the Multi Access Blade, in the connector labeled spans 1 to 8. Place the second trunk card cable assembly into the connector on the right side of the breakout box and on the bottom of the Multi Access Blade, in the connector labeled spans 9 to 16.

Connecting E1 or T1 PRI Telephony Cables with Two Multi Access Blade MP-MA-16-PRIs

This configuration is supported only on a Cisco Unified MeetingPlace 8112.

To Connect E1 or T1 PRI Telephony Cables with Two Multi Access Blade MP-MA-16-PRIs

Step 1 Locate the following items that shipped with the Cisco Unified MeetingPlace 8112:

E1 or T1 PRI telephony cables.

Two breakout boxes, which should already be mounted above your Cisco Unified MeetingPlace 8112.

Trunk card interface cable assemblies (50-pin Amphenol cables).

 

Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server 6.x

2-26

OL-13417-01

Page 50
Image 50
Cisco Systems 8, 700 MHz manual OL-13417-01

700 MHz, 8 specifications

Cisco Systems has consistently been at the forefront of networking technology, and their latest offering, the 8,700 MHz, showcases the company's commitment to providing innovative solutions for high-performance and reliable connectivity. The 8,700 MHz represents a significant advancement in frequency utilization, optimizing bandwidth for a range of applications, especially in the context of increasing data demands in enterprise environments.

One of the main features of the Cisco 8,700 MHz is its enhanced capacity for managing high-traffic workloads. With the ability to support multiple channels simultaneously, this equipment is designed to cater to the needs of modern businesses that demand high-speed internet and seamless network performance. The technology behind this frequency supports both conventional and advanced modulation techniques, allowing for more efficient data transmission and improved signal integrity.

The 8,700 MHz utilizes cutting-edge technologies such as Software-Defined Networking (SDN) and Network Functions Virtualization (NFV). These technologies facilitate greater flexibility and scalability in network management, enabling organizations to dynamically adjust resources based on real-time traffic conditions. The integration of SDN allows for centralized control and automation of network operations, significantly reducing the need for manual configurations while enhancing responsiveness to network changes.

Security is another critical characteristic of the Cisco 8,700 MHz. It incorporates advanced encryption protocols and threat detection mechanisms to protect sensitive data while ensuring compliance with industry standards. The hardware is also equipped with redundant power supplies and failover capabilities, providing reliable operation and minimizing downtime.

Moreover, the 8,700 MHz is designed to be environmentally sustainable, incorporating energy-efficient components and practices. This commitment to sustainability aligns with Cisco’s broader corporate social responsibility goals and caters to enterprises looking to reduce their carbon footprint.

In summary, Cisco Systems' 8,700 MHz stands out due to its high capacity, flexibility, robust security measures, and environmentally friendly design. It is tailored to meet the evolving demands of the digital landscape, empowering businesses to enhance their connectivity and operational efficiency in a competitive environment. As organizations increasingly rely on robust networking solutions, the Cisco 8,700 MHz is positioned to be a vital component of future-ready infrastructures.