Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems AS5350, AS5400 manual State, Description, T1 or E1 DFC

Models: AS5350 AS5400

1 88

Download 88 pages 30.73 Kb

Page 61

State

Chapter 6 Troubleshooting

LEDs

Table 6-1 LEDs

DFC	LED	State	Description

T1 or E1 DFC	ACTIVITY (ACT)	Fast flicker (Green)	Indicates DFC is up and running.

		Slow flicker (Green)	Indicates DFC is not yet fully
			functional.

	OK/MAINT	Green	The T1 or E1 DFC has passed initial
			power-up diagnostics tests and is
			operating normally.

		Yellow	The T1 or E1 DFC is not functioning.
			See the console for messages.

		Off	Indicates that all calls associated
			with the card are shut down and it is
			safe to remove the card with the
			system powered on.

	Remote Alarm	On (Yellow)	One LED below each T1/E1 port
	(RA), Local Alarm		indicates one of the following:
	(LA), or Loopback		• A local or remote loopback
	(LB)		• A local or remote loopback
	(LB)		diagnostic test is running on the
			diagnostic test is running on the
			associated T1 port.
			• An alarm is received on the
			associated T1/E1 port, indicating
			loss of signal (LOS) or loss of
			multiframe alignment (LOF) at
			the local or remote node.

Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide

	78-13311-01	6-3

Image 61

Cisco Systems AS5350, AS5400 manual State, Description, T1 or E1 DFC

Contents

Installation Guide Corporate HeadquartersCisco AS5350 and Cisco AS5400 Universal Gateway Card Cisco Systems, Inc 170 West Tasman Drive San Jose, CACisco AS5350 and Cisco AS5400 Universal Gateway Card Turn the television or radio antenna until the interference stopsCopyright 2001, Cisco Systems, Inc All rights reservedOnline Installation and Removal of the T1 or E1 DFC Safety Warnings, Recommendations, and Tools RequiredWhere to Go Next PrefaceTroubleshooting ConfigurationVerification OverviewContents Cabling SpecificationsGetting Help Attaching the 8-Port Interface Cable to a Bracket Optional A-578-13311-01 ContentsSafety Warnings Related Documentation, page New Hardware Features, pageDial Feature Card and T1 and E1 Dial FeatureCabling Specifications TroubleshootingDocument Conventions ConventionWaarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risicos en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information Informatie over naleving van veiligheids- en andere voorschriften raadplegen dat bij dit toestel is ingesloten Page World Wide Web Obtaining DocumentationDocumentation CD-ROM Ordering DocumentationObtaining Technical Assistance Contacting TAC by Using the Cisco TAC WebsiteCisco.com Technical Assistance CenterRelated Documentation New Hardware FeaturesContacting TAC by Telephone xiii78-13311-01 Preface New Hardware FeaturesGeneral Safety Safety Warnings, Recommendations, and Tools RequiredGeneral Safety, page Maintaining Safety with Electricity, page Required Tools and Equipment, page Where to Go Next, pageMaintaining Safety with Electricity Required Tools and Equipment Preventing Electrostatic DischargeChapter 2, “Dial Feature Card and Carrier Card Guidelines” Where to Go NextChapter 3, “T1 and E1 Dial Feature Cards” Chapter 4, “T3 Dial Feature Card”Removing and Installing Populated Carrier Cards, page Dial Feature Card and Carrier Card GuidelinesGetting Help, page Where to Go Next, page Dial Feature CardsChapter 4, “T3 Dial Feature Card,” to perform OIR of the T3 DFC Removing and Installing Populated Carrier CardsOnline Insertion and Removal OIR of DFCs Step 1 Power off the chassis Removing a Populated Carrier CardTo remove a populated carrier card, follow the steps below Figure 2-4 Removing the Carrier Card from the Cisco AS5350 Figure 2-3 Loosen the Captive Screws on the Cisco AS5400Figure 2-5 Removing the Carrier Card from the Cisco AS5400 cardInstalling a Populated Carrier Card Step 6 Reconnect all interface cables Chapter 4, “T3 Dial Feature Card.” Chapter 3, “T1 and E1 Dial Feature Cards.”Chapter 5, “Universal Port Dial Feature Card.” Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.”Where to Go Next Chapter 2 Dial Feature Card and Carrier Card Guidelines78-13311-01 Online Installation and Removal of the T1 or E1 DFC, page T1 and E1 Dial Feature CardsConfiguring Input Impedance for the E1 DFC, page Getting Help, page Where to Go Next, pageSpecification SpecificationTable 3-1 T1 DFC Network Specifications Table 3-2 E1 DFC Network SpecificationsOverview Online Installation and Removal of the T1 or E1 DFCRemoving the T1 or E1 DFC Router# clear port slot-number/port number Router# busyout slot-numberNote The clear port command only applies to the universal port DFC Figure 3-7 Loosen the Captive Screws on the Cisco AS5400 Figure 3-6 Loosen the Captive Screws on the Cisco AS5350Rx Tx Figure 3-9 Remove the DFC from the Cisco AS5400 Figure 3-8 Remove the DFC from the Cisco AS5350Figure 3-10 Blank DFC Cover Online Installation and Removal of the T1 or E1 DFC Chapter 3 T1 and E1 Dial Feature CardsRouter# show controller e1 6/0 timeslot Router# show busyoutOnline Installation and Removal of the T1 or E1 DFC Chapter 3 T1 and E1 Dial Feature CardsRouter# show busyout show chassis slotInstalling the T1 or E1 DFC Figure 3-12 Install the T1 or E1 DFC in the Cisco AS5400 3-10Figure 3-13 Tighten the Captive Screws on the Cisco AS5350 Figure 3-14 Tighten the Captive Screws on the Cisco AS5400Configuration Configuring Input Impedance for the E1 DFCCommand VerificationChapter 3 T1 and E1 Dial Feature Cards 3-12Configuring Input Impedance for the E1 DFC service udp-small-servers service tcp-small-serversChapter 3 T1 and E1 Dial Feature Cards 3-13Configuring Input Impedance for the E1 DFC Where to Go Next 3-14Chapter 4, “T3 Dial Feature Card.” Chapter 5, “Universal Port Dial Feature Card.”Online Installation and Removal OIR of the T3 DFC, page T3 Dial Feature CardGetting Help, page Where to Go Next, page OverviewRemoving the T3 DFC Online Installation and Removal OIR of the T3 DFCOverview Figure 4-2 Slot Numbering on the Cisco AS5350 ChassisRouter# clear port slot-number/port number Router# busyout slot-numberFigure 4-3 Slot Numbering on the Cisco AS5400 Chassis Figure 4-5 Loosen the Captive Screws on the Cisco AS5400 Figure 4-4 Loosen the Captive Screws on the Cisco AS5350Figure 4-6 Remove the DFC from the Cisco AS5350 Installing the T3 DFCFigure 4-7 Remove the DFC from the Cisco AS5400 Figure 4-8 Blank DFC CoverFigure 4-10 Install the T3 DFC in the Cisco AS5400 Figure 4-9 Install the T3 DFC in the Cisco AS5350Figure 4-11 Tighten the Captive Screws on the Cisco AS5350 Chapter 5, “Universal Port Dial Feature Card.” Where to Go NextChapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.” Getting Help78-13311-01 Chapter 4 T3 Dial Feature Card Where to Go NextSPE Firmware, page Getting Help, page Where to Go Next, page Universal Port Dial Feature CardOnline Insertion and Removal OIR of the Universal Port DFC, page OverviewRemoving the Universal Port DFC Online Insertion and Removal OIR of the Universal Port DFCOverview Figure 5-2 Slot Numbering on the Cisco AS5350 ChassisRouter# clear port slot-number/port number Router# busyout slot-numberFigure 5-3 Slot Numbering on the Cisco AS5400 Chassis Figure 5-5 Loosen the Captive Screws on the Cisco AS5400 Figure 5-4 Loosen the Captive Screws on the Cisco AS5350Figure 5-6 Remove the DFC from the Cisco AS5350 Figure 5-7 Remove the DFC from the Cisco AS5400 Chapter 5 Universal Port Dial Feature CardFigure 5-8 Blank DFC Cover Online Insertion and Removal OIR of the Universal Port DFCOnline Insertion and Removal OIR of the Universal Port DFC Chapter 5 Universal Port Dial Feature CardRouter# clear port Router# show busyoutFigure 5-9 Install the Universal Port DFC in the Cisco AS5350 Installing the Universal Port DFCFigure 5-10 Install the Universal Port DFC in the Cisco AS5400 Figure 5-12 Tighten the Captive Screws on the Cisco AS5400 Figure 5-11 Tighten the Captive Screws on the Cisco AS5350Where to Go Next SPE FirmwareChapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.” Getting HelpChapter 5 Universal Port Dial Feature Card Where to Go Next 5-1078-13311-01 Using the Bantam Jacks for Test Port Functionality, page TroubleshootingTroubleshooting Network Interfaces, page Getting Help, page LEDsFigure 6-2 8-Port T1 or E1 DFC LEDs Local alarmFigure 6-3 T3 DFC LEDs ACTIVITY ACT OK/MAINTDescription StateT1 or E1 DFC Description StateTable 6-1 LEDs continued State Mixing WAN DFCsDescription One CT3 DFC and up to two T1 DFCs any combination of 2, 4, or 8-portOverview Environment MonitoringFigure 6-5 Slot Numbering on the Cisco AS5350 Chassis Figure 6-6 Slot Numbering on the Cisco AS5400 Chassisinlet is measured as 22C/71F Displaying Environment Statusoutlet is measured as 27C/80F Router show environment Chapter 6 Troubleshooting Environment Monitoring78-13311-01 Monitoring Mode for the T1, E1 and T3 DFCs Using the Bantam Jacks for Test Port FunctionalityDrop and Insert Mode for the CT3 DFC 6-10 Troubleshooting Network InterfacesGetting Help Router# test trunk drop-insert on t1portT1 and E1 Cable and Port Pinouts Cabling Specifications2-Port and 4-Port T1 or E1 DFC A P P E N D I X ADirection SignalDB-15 Pin SignalTwinax Pin BNC PinRJ-45 TE Pin SignalRJ-45 T1 Pin RJ-45 NT PinSignal SignalBare 8-Port T1 or E1 DFCCable Description Part NumberFrom Male and Female RJ-45 CAB-DFC-OCTAL-xMFSignal SignalSignal SignalMale and Female RJ-45 CAB-DFC-OCTAL-xMF FromAttaching the 8-Port Interface Cable to a Bracket Optional Page A-10 Figure A-10 Securing the Cable Bracket to the Rack A-11Figure A-11 Connecting the 36-Pin Cable Connector to an 8-Port T1 DFC A-12Bantam Jack Port Pinouts CT3 Cable and Port PinoutsA-13 DescriptionAppendix A Cabling Specifications Bantam Jack Port Pinouts A-1478-13311-01 I N D E NumericsIN-1 IN-2 IN-3 IN-4 IN-5 Index IN-678-13311-01