Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems AS5350, AS5400 manual Mixing WAN DFCs, State, Description

Models: AS5350 AS5400

1 88

Download 88 pages 30.73 Kb

Page 63

Mixing WAN DFCs

Chapter 6 Troubleshooting

LEDs

Table 6-1 LEDs (continued)

	DFC	LED	State	Description

	Universal Port	ACTIVITY (ACT)	Flickering	There is call activity on the DFC.
	DFC
	DFC	OK/MAINT	On	The DFC passed the initial power-up
		OK/MAINT	On	The DFC passed the initial power-up
				diagnostic tests and is operating
				normally.

			Off	Indicates that all calls associated
				with the card are shut down and it is
				safe to remove the card with the
				system powered on.

1. To display information about an M13 alarm, use the show CT3 EXEC command.

Mixing WAN DFCs

The Cisco AS5350 and Cisco AS5400 support only one type of WAN DFC at a time. The DFCs that can be installed at one time are:

•Up to three T1 DFCs (any combination of 2, 4, or 8-port) or

•Up to three E1 DFCs (any combination of 2, 4, or 8-port) or

•One CT3 DFC or

•One CT3 DFC and up to two T1 DFCs (any combination of 2, 4, or 8-port)

The universal gateway software recognizes DFCs in the order of the slots they are in. For example, a DFC in slot 2 will be recognized before a DFC in slot 3. The system will recognize if there is a mix of WAN DFCs during both power up and OIR:

•During power up, the first WAN DFC recognized by the system will be the only type brought up.

•If there are two or more WAN DFCs of the same type and one is hot-swapped with another of a different type, the new one will not be recognized.

In both situations, an error message will appear on the console that is similar to:

00:01:12:%CARRIER-2-T1_E1_MIX:Cannot mix T1 and E1 8PRI DFC cards in chassis, do not power up invalid card in slot 7

Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide

	78-13311-01	6-5

Image 63

Cisco Systems AS5350, AS5400 manual Mixing WAN DFCs, State, Description

Contents

Cisco Systems, Inc 170 West Tasman Drive San Jose, CA Corporate HeadquartersInstallation Guide Cisco AS5350 and Cisco AS5400 Universal Gateway CardAll rights reserved Turn the television or radio antenna until the interference stopsCisco AS5350 and Cisco AS5400 Universal Gateway Card Copyright 2001, Cisco Systems, IncPreface Safety Warnings, Recommendations, and Tools RequiredOnline Installation and Removal of the T1 or E1 DFC Where to Go NextOverview ConfigurationTroubleshooting VerificationAttaching the 8-Port Interface Cable to a Bracket Optional A-5 Cabling SpecificationsContents Getting Help78-13311-01 ContentsT1 and E1 Dial Feature Related Documentation, page New Hardware Features, pageSafety Warnings Dial Feature Card andConvention TroubleshootingCabling Specifications Document ConventionsWaarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risicos en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information Informatie over naleving van veiligheids- en andere voorschriften raadplegen dat bij dit toestel is ingesloten Page Ordering Documentation Obtaining DocumentationWorld Wide Web Documentation CD-ROMTechnical Assistance Center Contacting TAC by Using the Cisco TAC WebsiteObtaining Technical Assistance Cisco.comxiii New Hardware FeaturesRelated Documentation Contacting TAC by Telephone78-13311-01 Preface New Hardware FeaturesRequired Tools and Equipment, page Where to Go Next, page Safety Warnings, Recommendations, and Tools RequiredGeneral Safety General Safety, page Maintaining Safety with Electricity, pageMaintaining Safety with Electricity Required Tools and Equipment Preventing Electrostatic DischargeChapter 4, “T3 Dial Feature Card” Where to Go NextChapter 2, “Dial Feature Card and Carrier Card Guidelines” Chapter 3, “T1 and E1 Dial Feature Cards”Dial Feature Cards Dial Feature Card and Carrier Card GuidelinesRemoving and Installing Populated Carrier Cards, page Getting Help, page Where to Go Next, pageRemoving and Installing Populated Carrier Cards Chapter 4, “T3 Dial Feature Card,” to perform OIR of the T3 DFCOnline Insertion and Removal OIR of DFCs Removing a Populated Carrier Card Step 1 Power off the chassisTo remove a populated carrier card, follow the steps below card Figure 2-3 Loosen the Captive Screws on the Cisco AS5400Figure 2-4 Removing the Carrier Card from the Cisco AS5350 Figure 2-5 Removing the Carrier Card from the Cisco AS5400Installing a Populated Carrier Card Step 6 Reconnect all interface cables Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.” Chapter 3, “T1 and E1 Dial Feature Cards.”Chapter 4, “T3 Dial Feature Card.” Chapter 5, “Universal Port Dial Feature Card.”Chapter 2 Dial Feature Card and Carrier Card Guidelines Where to Go Next78-13311-01 Where to Go Next, page T1 and E1 Dial Feature CardsOnline Installation and Removal of the T1 or E1 DFC, page Configuring Input Impedance for the E1 DFC, page Getting Help, pageTable 3-2 E1 DFC Network Specifications SpecificationSpecification Table 3-1 T1 DFC Network SpecificationsOnline Installation and Removal of the T1 or E1 DFC OverviewRemoving the T1 or E1 DFC Router# busyout slot-number Router# clear port slot-number/port numberNote The clear port command only applies to the universal port DFC Figure 3-6 Loosen the Captive Screws on the Cisco AS5350 Figure 3-7 Loosen the Captive Screws on the Cisco AS5400Rx Tx Figure 3-8 Remove the DFC from the Cisco AS5350 Figure 3-9 Remove the DFC from the Cisco AS5400Figure 3-10 Blank DFC Cover Router# show busyout Chapter 3 T1 and E1 Dial Feature CardsOnline Installation and Removal of the T1 or E1 DFC Router# show controller e1 6/0 timeslotshow chassis slot Chapter 3 T1 and E1 Dial Feature CardsOnline Installation and Removal of the T1 or E1 DFC Router# show busyoutInstalling the T1 or E1 DFC Figure 3-14 Tighten the Captive Screws on the Cisco AS5400 3-10Figure 3-12 Install the T1 or E1 DFC in the Cisco AS5400 Figure 3-13 Tighten the Captive Screws on the Cisco AS5350Verification Configuring Input Impedance for the E1 DFCConfiguration Commandservice udp-small-servers service tcp-small-servers 3-12Chapter 3 T1 and E1 Dial Feature Cards Configuring Input Impedance for the E1 DFC3-13 Chapter 3 T1 and E1 Dial Feature CardsConfiguring Input Impedance for the E1 DFC Chapter 5, “Universal Port Dial Feature Card.” 3-14Where to Go Next Chapter 4, “T3 Dial Feature Card.”Overview T3 Dial Feature CardOnline Installation and Removal OIR of the T3 DFC, page Getting Help, page Where to Go Next, pageFigure 4-2 Slot Numbering on the Cisco AS5350 Chassis Online Installation and Removal OIR of the T3 DFCRemoving the T3 DFC OverviewRouter# busyout slot-number Router# clear port slot-number/port numberFigure 4-3 Slot Numbering on the Cisco AS5400 Chassis Figure 4-5 Loosen the Captive Screws on the Cisco AS5400 Figure 4-4 Loosen the Captive Screws on the Cisco AS5350Figure 4-8 Blank DFC Cover Installing the T3 DFCFigure 4-6 Remove the DFC from the Cisco AS5350 Figure 4-7 Remove the DFC from the Cisco AS5400Figure 4-9 Install the T3 DFC in the Cisco AS5350 Figure 4-10 Install the T3 DFC in the Cisco AS5400Figure 4-11 Tighten the Captive Screws on the Cisco AS5350 Getting Help Where to Go NextChapter 5, “Universal Port Dial Feature Card.” Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.”78-13311-01 Chapter 4 T3 Dial Feature Card Where to Go NextOverview Universal Port Dial Feature CardSPE Firmware, page Getting Help, page Where to Go Next, page Online Insertion and Removal OIR of the Universal Port DFC, pageFigure 5-2 Slot Numbering on the Cisco AS5350 Chassis Online Insertion and Removal OIR of the Universal Port DFCRemoving the Universal Port DFC OverviewRouter# busyout slot-number Router# clear port slot-number/port numberFigure 5-3 Slot Numbering on the Cisco AS5400 Chassis Figure 5-4 Loosen the Captive Screws on the Cisco AS5350 Figure 5-5 Loosen the Captive Screws on the Cisco AS5400Figure 5-6 Remove the DFC from the Cisco AS5350 Online Insertion and Removal OIR of the Universal Port DFC Chapter 5 Universal Port Dial Feature CardFigure 5-7 Remove the DFC from the Cisco AS5400 Figure 5-8 Blank DFC CoverRouter# show busyout Chapter 5 Universal Port Dial Feature CardOnline Insertion and Removal OIR of the Universal Port DFC Router# clear portInstalling the Universal Port DFC Figure 5-9 Install the Universal Port DFC in the Cisco AS5350Figure 5-10 Install the Universal Port DFC in the Cisco AS5400 Figure 5-12 Tighten the Captive Screws on the Cisco AS5400 Figure 5-11 Tighten the Captive Screws on the Cisco AS5350Getting Help SPE FirmwareWhere to Go Next Chapter 6, “Troubleshooting.” Appendix A, “Cabling Specifications.”5-10 Chapter 5 Universal Port Dial Feature Card Where to Go Next78-13311-01 LEDs TroubleshootingUsing the Bantam Jacks for Test Port Functionality, page Troubleshooting Network Interfaces, page Getting Help, pageACTIVITY ACT OK/MAINT Local alarmFigure 6-2 8-Port T1 or E1 DFC LEDs Figure 6-3 T3 DFC LEDsState DescriptionT1 or E1 DFC State DescriptionTable 6-1 LEDs continued One CT3 DFC and up to two T1 DFCs any combination of 2, 4, or 8-port Mixing WAN DFCsState DescriptionFigure 6-6 Slot Numbering on the Cisco AS5400 Chassis Environment MonitoringOverview Figure 6-5 Slot Numbering on the Cisco AS5350 ChassisDisplaying Environment Status inlet is measured as 22C/71Foutlet is measured as 27C/80F Chapter 6 Troubleshooting Environment Monitoring Router show environment78-13311-01 Using the Bantam Jacks for Test Port Functionality Monitoring Mode for the T1, E1 and T3 DFCsDrop and Insert Mode for the CT3 DFC Router# test trunk drop-insert on t1port Troubleshooting Network Interfaces6-10 Getting HelpA P P E N D I X A Cabling SpecificationsT1 and E1 Cable and Port Pinouts 2-Port and 4-Port T1 or E1 DFCSignal SignalDirection DB-15 PinSignal BNC PinTwinax Pin RJ-45 TE PinSignal RJ-45 NT PinRJ-45 T1 Pin SignalPart Number 8-Port T1 or E1 DFCBare Cable DescriptionSignal Male and Female RJ-45 CAB-DFC-OCTAL-xMFFrom SignalFrom SignalSignal Male and Female RJ-45 CAB-DFC-OCTAL-xMFAttaching the 8-Port Interface Cable to a Bracket Optional Page A-10 Figure A-10 Securing the Cable Bracket to the Rack A-11Figure A-11 Connecting the 36-Pin Cable Connector to an 8-Port T1 DFC A-12Description CT3 Cable and Port PinoutsBantam Jack Port Pinouts A-13A-14 Appendix A Cabling Specifications Bantam Jack Port Pinouts78-13311-01 Numerics I N D EIN-1 IN-2 IN-3 IN-4 IN-5 IN-6 Index78-13311-01